Regardless it’s for your own personal security, for roadworthiness testing or to avoid a fine, making sure your headlamp bulbs are in every case effective is very important. In reality, bulbs are wearing parts that will predictably burn out after some time and as a result need to be replaced. You’re almost certainly on the website because one of your parking lights is burnt out and you’re struggling with how to change your CUPRA FORMENTOR’s license plate bulb, we’ve written this article to help you do it on your own and not have to go to your motor mechanic. Firstly, we will examine changing the license plate bulb from the outside, secondly, how to replace the license plate bulb without outside access, and thirdly, how to replace the rear license plate bulb of your CUPRA FORMENTOR.
How to swap the license plate bulb on your CUPRA FORMENTOR throughout the outside
This technique is the most simple of the two, actually, for this one you will just have to take off the protective covers of the bulbs. Regrettably on some years or packages of car these covers do not open from the outside and if this is the case we will spend a moment on in the second section of this article content to demonstrate the approach.
So let’s start with swapping the number plate bulb by going through the outside of your CUPRA FORMENTOR. Regardless it’s the front or the back of your car the procedure will be identical.
Here are a few simple actions to follow to execute this maintenance:
- With the engine off, disconnect the battery terminals from your car
- Face your license plate and use a flat screwdriver or knife to insert the flat part into the notch assigned for this purpose (commonly on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your CUPRA FORMENTOR
- Use your screwdriver or knife to eject the bulb from its spot, in the event you are afraid of destroying anything, you can also do it with your fingers.
- Finally, put the new license plate light bulb
- Last stage, before reassembling, reconnect your battery and check the light to confirm the success of the procedure.
.
How to change the number plate bulb on your CUPRA FORMENTOR without outside access
Second section of our article, replace this license plate bulb on your CUPRA FORMENTOR without external access. Generally you will be able to access it, nevertheless some series (often at the rear does not allow this access).
How to swap the front license plate bulb on my CUPRA FORMENTOR
To swap the one on the front plate, nothing could be less difficult, you will have to put yourself under the car (preferably put on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, commonly kept by two soft plastic tabs by pressing on both simultaneously, then once you have your license plate bulb block in hand, Remove the plastic that acts as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (be attentive not to exert too much pressure otherwise you will break the plastic cover), and you will only have to take off the burnt-out license plate bulb and replace it with the new , then verify and reassemble the whole thing.
How to swap the rear license plate bulb on my CUPRA FORMENTOR
Finally last possibility, you must swap the bulb on the backplate of your CUPRA FORMENTOR, but you simply cannot open the cover from the outside of your car. In this instance, here is the approach to accomplish this task:
- Unplug the battery from your CUPRA FORMENTOR
- Identify the position of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, kept by clips, you will have to lever gently on all the frame of the trunk to remove it.
- Once found, before removing the bulb holders, disconnect the holders for less difficult access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Change the burnt-out license plate bulb on your CUPRA FORMENTOR, check it and reassemble it, paying attention to the clips on the trunk liner
.
.
There you have it, you have found out the main methods for swapping license plate bulbs on your car, be aware that on some models the technique may be a bit different but you should be able to accomplish it following the outline of this document. If you can’t do it, don’t be reluctant to go to your workshop it would be a shame to break a part of your CUPRA FORMENTOR. If you wish to change other bulbs like the position light bulbs on your CUPRA FORMENTOR or the low beam bulbs on CUPRA FORMENTOR, don’t be reluctant to browse our articles which describe you the operation to follow.
Whenever you have any additional questions about the CUPRA FORMENTOR, do not hesitate to consult our CUPRA FORMENTOR category.
