Whether it’s for your own safety, for roadworthiness tests or to avoid a fine, making sure your headlamp bulbs are in every case effective is very important. In reality, bulbs are wearing units that will obviously burn out after a while and therefore need to be replaced. You’re almost certainly on this site because one of your parking lights is burnt out and you’re questioning how to change your Citroen Jumper 2’s license plate bulb, we’ve created this content page to help you do it without any help and not have to go to your technician. Firstly, we will look at changing the license plate bulb from the outside, secondly, how to replace the license plate bulb without outside access, and thirdly, how to replace the rear license plate bulb of your Citroen Jumper 2.
How to replace the license plate bulb on your Citroen Jumper 2 through the outside
This method is the most simple of the two, in truth, for this one you will just require to take out the protective covers of the bulbs. Sadly on some years or packages of car these covers do not open from the outside and if this is the case we will take a moment on in the second part of this article content to demonstrate the method.
So let’s start with changing the number plate bulb by going through the outside of your Citroen Jumper 2. Whether it’s the front or the back of your motor vehicle the technique will be similar.
Here are a few simple guidelines to stick to to perform this maintenance tasks:
- With the engine off, disconnect the battery terminals from your car
- Face your license plate and use a flat screwdriver or knife to insert the flat part into the notch supplied for this purpose (commonly on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Citroen Jumper 2
- Use your screwdriver or knife to remove the bulb from its place, in the event you are scared of destroying anything, you can as well do it with your fingers.
- Finally, put the new license plate light bulb
- Last step, before reassembling, reconnect your battery and verify the light to validate the success of the operation.
.
How to replace the number plate bulb on your Citroen Jumper 2 without outside access
Second part of our content, swap this license plate bulb on your Citroen Jumper 2 without external access. Most often you will be able to access it, but some series (often at the rear does not allow this access).
How to replace the front license plate bulb on my Citroen Jumper 2
To replace the one on the front plate, nothing could be easier, you will have to put yourself under the motor vehicle (preferably positioned on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, commonly kept by two soft plastic tabs by pressing on both simultaneously, then right after you have your license plate bulb block in hand, Remove the plastic that acts as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (take extra care not to put in too much force otherwise you will break the plastic cover), and you will just have to take out the burnt-out license plate bulb and swap it with the new , then test and reassemble the whole thing.
How to replace the rear license plate bulb on my Citroen Jumper 2
Finally last solution, you must replace the bulb on the backplate of your Citroen Jumper 2, but you are not able to open the cover from the outside of your motor vehicle. In this case, here is the method to operate this operation:
- Disconnect the battery from your Citroen Jumper 2
- Identify the location of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, kept by clips, you will have to lever softly on all the frame of the trunk to remove it.
- Once located, before removing the bulb holders, disconnect the holders for less difficult access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Change the burnt-out license plate bulb on your Citroen Jumper 2, verify it and reassemble it, watching the clips on the trunk liner
.
.
There you have it, you have learned the main techniques for changing license plate bulbs on your car, take notice that on some models the method may be a bit different but you should be able to accomplish it following the outline of this content page. If you can’t do it, don’t be reluctant to go to your mechanic it would be a shame to break a part of your Citroen Jumper 2. If you need to change other bulbs like the position light bulbs on your Citroen Jumper 2 or the low beam bulbs on Citroen Jumper 2, don’t be reluctant to consult our content articles which describe you the process to follow.
To get more tips on the Citroen Jumper 2, take a look at the Citroen Jumper 2 category.
