It doesn’t matter if it’s for your personal safety, for roadworthiness tests or to avoid a fine, being sure your headlamp bulbs are constantly effective is really important. In fact, bulbs are wearing auto parts that will inevitably burn out in the future and therefore need to be changed. You’re most certainly on this website because one of your parking lights is burnt out and you’re worried about how to change your Chrysler 300’s license plate bulb, we’ve written and published this content page to help you do it on your own and not have to go to your auto mechanic. Firstly, we will look at changing the license plate bulb from the outside, secondly, how to change the license plate bulb without outside access, and thirdly, how to change the rear license plate bulb of your Chrysler 300.
How to change the license plate bulb on your Chrysler 300 throughout the outside
This option is the simplest of the two, in reality, for this one you will only need to take off the protective covers of the bulbs. Sadly on some years or packages of car these covers do not open from the outside and if this is the situation we will spend some time on in the second section of this content page to describe the method.
So let’s begin with replacing the number plate bulb by going through the outside of your Chrysler 300. It doesn’t matter if it’s the front or the back of your vehicle the method will be identical.
Here are a few simple guidelines to follow to carry out this maintenance tasks:
- With the engine turned off, unplug the battery terminals from your car
- Position yourself in front of your license plate and use a flat screwdriver or knife to insert the flat part into the notch provided for this intent (commonly on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Chrysler 300
- Use your screwdriver or knife to eject the bulb from its spot, if you are scared of breaking anything, you can also do it with your fingers.
- Finally, position the new license plate light bulb
- Last stage, before reassembling, reconnect your battery and verify the light to validate the successfulness of the process.
.
How to change the number plate bulb on your Chrysler 300 without outside access
Second section of our content, swap this license plate bulb on your Chrysler 300 without external access. In most cases you will be able to access it, nevertheless some series (often at the rear does not allow this access).
How to change the front license plate bulb on my Chrysler 300
To change the one on the front plate, nothing could be less difficult, you will have to position yourself under the vehicle (ideally positioned on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, commonly kept by two soft plastic tabs by pressing on both at the same time, then now that you have your license plate bulb block in hand, Take away the plastic that acts as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (be careful not to exert too much pressure or you will break the plastic cover), and you will only have to take off the burnt-out license plate bulb and swap it with the new , then test out and reassemble the whole thing.
How to change the rear license plate bulb on my Chrysler 300
Finally last solution, you must change the bulb on the backplate of your Chrysler 300, but you simply cannot open the cover from the outside of your vehicle. In this case, here is the approach to carry out this operation:
- Unplug the battery from your Chrysler 300
- Find the location of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, kept by clips, you will have to lever delicately on all the frame of the trunk to remove it.
- Once located, before removing the bulb holders, unplug the holders for easier access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Change the burnt-out license plate bulb on your Chrysler 300, verify it and reassemble it, paying attention to the clips on the trunk liner
.
.
There you have it, you have found out the main methods for replacing license plate bulbs on your car, remember that on some models the method may be a bit different but you should be able to accomplish it following the outline of this content page. If you can’t do it, don’t be reluctant to go to your garage it would be a shame to break a part of your Chrysler 300. If you desire to change other bulbs like the position light bulbs on your Chrysler 300 or the low beam bulbs on Chrysler 300, don’t be reluctant to consult our articles which describe you the procedure to follow.
In the event that you have any additional questions about the Chrysler 300, do not hesitate to consult our Chrysler 300 category.
