Whether it’s for your specific safety, for roadworthiness tests or to avoid a fine, ensuring that your headlamp bulbs are in every case working is very important. Indeed, bulbs are wearing units that will undoubtedly burn out over the years and consequently need to be changed. You’re quite likely on this site because one of your parking lights is burnt out and you’re wondering how to change your Chevrolet Trax’s license plate bulb, we’ve made this content to help you do it without any help and not have to go to your auto mechanic. Firstly, we will examine changing the license plate bulb from the outside, secondly, how to replace the license plate bulb without outside access, and thirdly, how to replace the rear license plate bulb of your Chevrolet Trax.
How to replace the license plate bulb on your Chevrolet Trax throughout the outside
This method is the quickest of the two, in truth, for this one you will just need to take out the protective covers of the bulbs. Sadly on some years or packages of car these covers do not open from the outside and if this is the case we will spend some time on in the second part of this content page to show you the approach.
So let’s begin with changing the number plate bulb by going through the outside of your Chevrolet Trax. Whether it’s the front or the back of your automobile the procedure will be identical.
Here are a few simple actions to follow to conduct this maintenance tasks:
- With the engine turned off, disconnect the battery terminals from your car
- Face your license plate and use a flat screwdriver or knife to insert the flat part into the notch assigned for this purpose (in most cases on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Chevrolet Trax
- Use your screwdriver or knife to eject the bulb from its location, in the event you are scared of breaking something, you can also do it with your fingers.
- Finally, position the new license plate light bulb
- Last step, before reassembling, reconnect your battery and check the light to validate the successfulness of the task.
.
How to replace the number plate bulb on your Chevrolet Trax without outside access
Second part of our document, swap this license plate bulb on your Chevrolet Trax without external access. Most often you will be able to access it, nevertheless some series (often at the rear does not allow this access).
How to replace the front license plate bulb on my Chevrolet Trax
To replace the one on the front plate, nothing could be less hard, you will have to position yourself under the automobile (preferably placed on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, in most cases kept by two soft plastic tabs by pressing on both at once, then right after you have your license plate bulb block in hand, Take off the plastic that acts as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (be mindful not to apply too much pressure otherwise you will break the plastic cover), and you will simply have to take out the burnt-out license plate bulb and swap it with the new , then test and reassemble the whole thing.
How to replace the rear license plate bulb on my Chevrolet Trax
Finally last possibility, you must replace the bulb on the backplate of your Chevrolet Trax, but you are not able to open the cover from the outside of your automobile. In this instance, here is the technique to accomplish this operation:
- Unplug the battery from your Chevrolet Trax
- Find the spot of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, kept by clips, you will have to lever softly on all the frame of the trunk to remove it.
- Once established, before removing the bulb holders, disconnect the holders for less complicated access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Change the burnt-out license plate bulb on your Chevrolet Trax, check it and reassemble it, watching the clips on the trunk liner
.
.
There you have it, you have found out the main solutions for changing license plate bulbs on your car, remember that on some models the technique may be a bit different but you should be able to do it following the outline of this content. If you can’t do it, don’t hesitate to go to your garage it would be a shame to break a part of your Chevrolet Trax. If you wish to change other bulbs like the position light bulbs on your Chevrolet Trax or the low beam bulbs on Chevrolet Trax, don’t hesitate to read our articles which explain you the process to follow.
To find more tips on the Chevrolet Trax, take a look at the Chevrolet Trax category.
