Regardless whether it’s for your own security, for roadworthiness tests or to avoid a fine, ensuring that your headlamp bulbs are always functioning is necessary. In reality, bulbs are wearing parts that will predictably burn out over time and as a result need to be swapped out. You’re perhaps here because one of your parking lights is burnt out and you’re struggling with how to change your Chevrolet Tahoe’s license plate bulb, we’ve written this content to help you do it all on your own and not have to go to your auto technician. Firstly, we will take a look at changing the license plate bulb from the outside, secondly, how to replace the license plate bulb without outside access, and thirdly, how to replace the rear license plate bulb of your Chevrolet Tahoe.
How to change the license plate bulb on your Chevrolet Tahoe through the outside
This option is the least difficult of the two, in reality, for this one you will only have to take away the protective covers of the bulbs. Regrettably on some years or packages of car these covers do not open from the outside and if this is the situation we will take some time on in the second part of this content to clarify the way.
So let’s begin with swapping the number plate bulb by going through the outside of your Chevrolet Tahoe. Regardless whether it’s the front or the back of your automobile the process will be the same.
Here are a few simple guidelines to stick to to perform this maintenance tasks:
- With the engine turned off, unplug the battery terminals from your car
- Position yourself in front of your license plate and use a flat screwdriver or knife to insert the flat part into the notch specified for this purpose (in most cases on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Chevrolet Tahoe
- Use your screwdriver or knife to remove the bulb from its spot, in the event you are worried of damaging something, you can also do it with your fingers.
- Finally, position the new license plate light bulb
- Last step, before reassembling, reconnect your battery and check the light to confirm the successfulness of the operation.
.
How to replace the number plate bulb on your Chevrolet Tahoe without outside access
Second part of our content page, change this license plate bulb on your Chevrolet Tahoe without external access. Most often you will be able to access it, nevertheless some series (often at the rear does not allow this access).
How to change the front license plate bulb on my Chevrolet Tahoe
To change the one on the front plate, nothing could be much easier, you will have to position yourself under the automobile (ideally put on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, in most cases kept by two soft plastic tabs by pressing on both at once, then right after you have your license plate bulb block in hand, Take out the plastic that acts as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (take extra care not to apply too much pressure or you will break the plastic cover), and you will only have to take away the burnt-out license plate bulb and change it with the new , then verify and reassemble the whole thing.
How to change the rear license plate bulb on my Chevrolet Tahoe
Finally last possibility, you must change the bulb on the backplate of your Chevrolet Tahoe, but you cannot really open the cover from the outside of your automobile. In this instance, here is the solution to perform this operation:
- Disconnect the battery from your Chevrolet Tahoe
- Locate the spot of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, kept by clips, you will have to lever delicately on all the frame of the trunk to remove it.
- Once found, before removing the bulb holders, unplug the holders for less complicated access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Change the burnt-out license plate bulb on your Chevrolet Tahoe, check it and reassemble it, watching the clips on the trunk liner
.
.
There you have it, you have learned the main tactics for swapping license plate bulbs on your car, be aware that on some models the methodology may be a bit different but you should be able to accomplish it following the explanation of this content. If you can’t do it, don’t hesitate to go to your garage area it would be a shame to break a part of your Chevrolet Tahoe. If you wish to change other bulbs like the position light bulbs on your Chevrolet Tahoe or the low beam bulbs on Chevrolet Tahoe, don’t hesitate to consult our content articles which explain you the process to follow.
In the event that you have any further questions about the Chevrolet Tahoe, do not hesitate to consult our Chevrolet Tahoe category.
