Regardless it’s for your own personal safety, for roadworthiness tests or to avoid a fine, being certain your headlamp bulbs are always working is very important. In fact, bulbs are wearing parts that will undoubtedly burn out after a while and therefore need to be changed. You’re likely on this website because one of your parking lights is burnt out and you’re questioning how to change your Chevrolet Suburban’s license plate bulb, we’ve written and published this article to help you do it all on your own and not have to go to your mechanic. Firstly, we will examine changing the license plate bulb from the outside, secondly, how to replace the license plate bulb without outside access, and thirdly, how to replace the rear license plate bulb of your Chevrolet Suburban.

change-license-plate-bulb-chevrolet-suburban

How to replace the license plate bulb on your Chevrolet Suburban through the outside

This technique is the easiest of the two, in truth, for this one you will only need to take off the protective covers of the bulbs. Unfortunately on some years or packages of car these covers do not open from the outside and if this is the case we will dedicate some time on in the second part of this content to explain the approach.
So let’s begin with replacing the number plate bulb by going through the outside of your Chevrolet Suburban. Regardless it’s the front or the back of your car the technique will be similar.
Here are a few simple actions to follow to conduct this routine service:

  • With the engine off, disconnect the battery terminals from your car
  • Face your license plate and use a flat screwdriver or knife to place the flat part into the notch supplied for this intent (generally on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Chevrolet Suburban
  • .

  • Use your screwdriver or knife to remove the bulb from its place, in the event you are scared of damaging a thing, you can as well do it with your fingers.
  • Finally, put the new license plate light bulb
  • Last stage, before reassembling, reconnect your battery and verify the light to confirm the successfulness of the operation.

How to replace the number plate bulb on your Chevrolet Suburban without outside access

Second part of our content page, swap this license plate bulb on your Chevrolet Suburban without external access. In most cases you will be able to access it, but some series (often at the rear does not allow this access).

How to replace the front license plate bulb on my Chevrolet Suburban

To replace the one on the front plate, nothing could be much easier, you will have to put yourself under the car (ideally positioned on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, generally held by two soft plastic tabs by pressing on both at once, then right after you have your license plate bulb block in hand, Remove the plastic that operates as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (be attentive not to apply too much force or you will break the plastic cover), and you will only have to take off the burnt-out license plate bulb and swap it with the new , then test out and reassemble the whole thing.

How to replace the rear license plate bulb on my Chevrolet Suburban

Finally last possibility, you must replace the bulb on the backplate of your Chevrolet Suburban, but you are not able to open the cover from the outside of your car. In this case, here is the technique to perform this operation:

  • Unplug the battery from your Chevrolet Suburban
  • Identify the location of your light bulbs from the outside.
  • From the inside of the trunk, you have to remove the lining of the trunk, held by clips, you will have to lever softly on all the frame of the trunk to remove it.
  • Once located, before removing the bulb holders, disconnect the holders for much easier access.
  • Using a screwdriver, lever the two plastic parts to remove the bulb holder
  • .

  • Replace the burnt-out license plate bulb on your Chevrolet Suburban, verify it and reassemble it, watching the clips on the trunk liner

.
There you have it, you have found out the main solutions for replacing license plate bulbs on your car, be aware that on some models the technique may be a bit different but you should be able to accomplish it following the explanation of this article content. If you can’t do it, don’t hesitate to go to your mechanic it would be a shame to break a part of your Chevrolet Suburban. If you wish to change other bulbs like the position light bulbs on your Chevrolet Suburban or the low beam bulbs on Chevrolet Suburban, don’t hesitate to read our articles which explain you the process to follow.

If perhaps you have any additional questions about the Chevrolet Suburban, do not hesitate to consult our Chevrolet Suburban category.