Regardless it’s for your personal security, for roadworthiness tests or to avoid a fine, making sure your headlamp bulbs are in every case functional is fundamental. In fact, bulbs are wearing units that will obviously burn out after some time and as a result need to be swapped out. You’re most certainly on this website because one of your parking lights is burnt out and you’re struggling with how to change your Chevrolet Silverado’s license plate bulb, we’ve written this article to help you do it on your own and not have to go to your auto technician. Firstly, we will take a look at changing the license plate bulb from the outside, secondly, how to change the license plate bulb without outside access, and thirdly, how to change the rear license plate bulb of your Chevrolet Silverado.
How to replace the license plate bulb on your Chevrolet Silverado coming from the outside
This technique is the most simple of the two, in reality, for this one you will simply have to remove the protective covers of the bulbs. Sadly on some years or packages of car these covers do not open from the outside and if this is the situation we will dedicate some time on in the second section of this content to demonstrate the method.
So let’s start with replacing the number plate bulb by going through the outside of your Chevrolet Silverado. Regardless it’s the front or the back of your motor vehicle the procedure will be the same.
Here are a few simple guidelines to stick to to execute this maintenance tasks:
- With the engine turned off, disconnect the battery terminals from your car
- Face your license plate and use a flat screwdriver or knife to place the flat part into the notch specified for this intent (in general on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Chevrolet Silverado
- Use your screwdriver or knife to remove the bulb from its place, in the event that you are scared of damaging anything, you can as well do it with your fingers.
- Finally, put the new license plate light bulb
- Last step, before reassembling, reconnect your battery and verify the light to validate the success of the task.
.
How to change the number plate bulb on your Chevrolet Silverado without outside access
Second section of our content, change this license plate bulb on your Chevrolet Silverado without external access. In most cases you will be able to access it, however some series (often at the rear does not allow this access).
How to replace the front license plate bulb on my Chevrolet Silverado
To replace the one on the front plate, nothing could be less complicated, you will have to put yourself under the motor vehicle (ideally positioned on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, in general kept by two soft plastic tabs by pressing on both at the same time, then right after you have your license plate bulb block in hand, Take off the plastic that works as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (take extra care not to exert too much pressure otherwise you will break the plastic cover), and you will just have to remove the burnt-out license plate bulb and replace it with the new , then verify and reassemble the whole thing.
How to replace the rear license plate bulb on my Chevrolet Silverado
Finally last solution, you must replace the bulb on the backplate of your Chevrolet Silverado, but you cannot really open the cover from the outside of your motor vehicle. In this instance, here is the process to conduct this task:
- Unplug the battery from your Chevrolet Silverado
- Identify the position of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, kept by clips, you will have to lever softly on all the frame of the trunk to remove it.
- Once found, before removing the bulb holders, disconnect the holders for less difficult access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Change the burnt-out license plate bulb on your Chevrolet Silverado, verify it and reassemble it, watching the clips on the trunk liner
.
.
There you have it, you have learned the main solutions for replacing license plate bulbs on your car, take notice that on some models the technique may be a bit different but you should be able to do it following the explanation of this document. If you can’t do it, don’t be reluctant to go to your garage area it would be a shame to break a part of your Chevrolet Silverado. If you wish to change other bulbs like the position light bulbs on your Chevrolet Silverado or the low beam bulbs on Chevrolet Silverado, don’t be reluctant to browse our articles which describe you the process to follow.
If you wish more tutorials on the Chevrolet Silverado, go to our Chevrolet Silverado category.
