Regardless whether it’s for your personal safety, for roadworthiness tests or to avoid a fine, being sure your headlamp bulbs are constantly functioning is extremely important. In fact, bulbs are wearing parts that will obviously burn out after some time and therefore need to be changed. You’re most likely on this website because one of your parking lights is burnt out and you’re wanting to know how to change your Chevrolet Malibu’s license plate bulb, we’ve created this article to help you do it on your own and not have to go to your motor mechanic. Firstly, we will examine changing the license plate bulb from the outside, secondly, how to replace the license plate bulb without outside access, and thirdly, how to replace the rear license plate bulb of your Chevrolet Malibu.
How to replace the license plate bulb on your Chevrolet Malibu through the outside
This technique is the easiest of the two, in truth, for this one you will just require to take out the protective covers of the bulbs. Regrettably on some years or packages of car these covers do not open from the outside and if this is the situation we will dedicate a moment on in the second part of this document to describe the way.
So let’s start with changing the number plate bulb by going through the outside of your Chevrolet Malibu. Regardless whether it’s the front or the back of your motor vehicle the technique will be similar.
Here are a few simple actions to stick to to conduct this service:
- With the engine turned off, unplug the battery terminals from your car
- Position yourself in front of your license plate and use a flat screwdriver or knife to insert the flat part into the notch assigned for this intent (generally on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Chevrolet Malibu
- Use your screwdriver or knife to eject the bulb from its location, if you are worried of destroying something, you can also do it with your fingers.
- Finally, put the new license plate light bulb
- Last stage, before reassembling, reconnect your battery and test the light to validate the achievement of the procedure.
.
How to change the number plate bulb on your Chevrolet Malibu without outside access
Second part of our article, swap this license plate bulb on your Chevrolet Malibu without external access. In most cases you will be able to access it, but some series (often at the rear does not allow this access).
How to replace the front license plate bulb on my Chevrolet Malibu
To replace the one on the front plate, nothing could be less difficult, you will have to put yourself under the motor vehicle (preferably placed on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, generally held by two soft plastic tabs by pressing on both simultaneously, then right after you have your license plate bulb block in hand, Take away the plastic that acts as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (take care not to exert too much pressure otherwise you will break the plastic cover), and you will simply have to take out the burnt-out license plate bulb and replace it with the new , then verify and reassemble the whole thing.
How to replace the rear license plate bulb on my Chevrolet Malibu
Finally last possibility, you must replace the bulb on the backplate of your Chevrolet Malibu, but you cannot open the cover from the outside of your motor vehicle. In such a case, here is the tactic to operate this task:
- Unplug the battery from your Chevrolet Malibu
- Find the spot of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, held by clips, you will have to lever gently on all the frame of the trunk to remove it.
- Once found, before removing the bulb holders, unplug the holders for less complicated access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Change the burnt-out license plate bulb on your Chevrolet Malibu, test it and reassemble it, paying attention to the clips on the trunk liner
.
.
There you have it, you have learned the main approaches for changing license plate bulbs on your car, take notice that on some models the methodology may be a bit different but you should be able to realize it following the outline of this content page. If you can’t do it, don’t hesitate to go to your garage area it would be a shame to break a part of your Chevrolet Malibu. If you desire to change other bulbs like the position light bulbs on your Chevrolet Malibu or the low beam bulbs on Chevrolet Malibu, don’t hesitate to browse our content articles which demonstrate you the procedure to follow.
To find more tips on the Chevrolet Malibu, take a look at the Chevrolet Malibu category.
