Regardless whether it’s for your own personal security, for roadworthiness tests or to avoid a fine, ensuring that your headlamp bulbs are in every case effective is very important. In reality, bulbs are wearing auto parts that will inevitably burn out over the years and consequently need to be replaced. You’re quite likely here because one of your parking lights is burnt out and you’re worried about how to change your Chevrolet City Express’s license plate bulb, we’ve created this document to help you do it by yourself and not have to go to your mechanic. Firstly, we will take a look at changing the license plate bulb from the outside, secondly, how to replace the license plate bulb without outside access, and thirdly, how to replace the rear license plate bulb of your Chevrolet City Express.
How to swap the license plate bulb on your Chevrolet City Express throughout the outside
This process is the most simple of the two, in truth, for this one you will simply need to take off the protective covers of the bulbs. Sadly on some years or packages of car these covers do not open from the outside and if this is the case we will spend some time on in the second section of this document to explain the approach.
So let’s begin with changing the number plate bulb by going through the outside of your Chevrolet City Express. Regardless whether it’s the front or the back of your motor vehicle the process will be identical.
Here are a few simple guidelines to follow to conduct this maintenance tasks:
- With the engine turned off, disconnect the battery terminals from your car
- Position yourself in front of your license plate and use a flat screwdriver or knife to place the flat part into the notch specified for this intent (usually on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Chevrolet City Express
- Use your screwdriver or knife to remove the bulb from its spot, if you are afraid of destroying anything, you can as well do it with your fingers.
- Finally, put the new license plate light bulb
- Last step, before reassembling, reconnect your battery and check the light to validate the achievement of the operation.
.
How to change the number plate bulb on your Chevrolet City Express without outside access
Second section of our content, replace this license plate bulb on your Chevrolet City Express without external access. In most cases you will be able to access it, however some series (often at the rear does not allow this access).
How to swap the front license plate bulb on my Chevrolet City Express
To swap the one on the front plate, nothing could be less complicated, you will have to put yourself under the motor vehicle (ideally placed on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, usually kept by two soft plastic tabs by pressing on both simultaneously, then right after you have your license plate bulb block in hand, Take off the plastic that works as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (be cautious not to apply too much force or you will break the plastic cover), and you will only have to take off the burnt-out license plate bulb and change it with the new , then test and reassemble the whole thing.
How to swap the rear license plate bulb on my Chevrolet City Express
Finally last solution, you must swap the bulb on the backplate of your Chevrolet City Express, but you are not able to open the cover from the outside of your motor vehicle. In such a case, here is the technique to carry out this task:
- Disconnect the battery from your Chevrolet City Express
- Find the spot of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, kept by clips, you will have to lever carefully on all the frame of the trunk to remove it.
- Once established, before removing the bulb holders, disconnect the holders for much easier access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Change the burnt-out license plate bulb on your Chevrolet City Express, check it and reassemble it, paying attention to the clips on the trunk liner
.
.
There you have it, you have found out the main approaches for changing license plate bulbs on your car, remember that on some models the methodology may be a bit different but you should be able to do it following the explanation of this content page. If you can’t do it, don’t be reluctant to go to your workshop it would be a shame to break a part of your Chevrolet City Express. If you desire to change other bulbs like the position light bulbs on your Chevrolet City Express or the low beam bulbs on Chevrolet City Express, don’t be reluctant to read our content articles which demonstrate you the operation to follow.
If you need more tutorials on the Chevrolet City Express, go to our Chevrolet City Express category.
