Whether it’s for your own personal security, for roadworthiness tests or to avoid a fine, being sure your headlamp bulbs are all the time functioning is necessary. In reality, bulbs are wearing units that will undoubtedly burn out with time and consequently need to be swapped out. You’re likely on the website because one of your parking lights is burnt out and you’re struggling with how to change your Chevrolet Avalanche’s license plate bulb, we’ve written this article content to help you do it on your own and not have to go to your auto mechanic. Firstly, we will look at changing the license plate bulb from the outside, secondly, how to change the license plate bulb without outside access, and thirdly, how to change the rear license plate bulb of your Chevrolet Avalanche.
How to swap the license plate bulb on your Chevrolet Avalanche throughout the outside
This technique is the simplest of the two, in truth, for this one you will only need to remove the protective covers of the bulbs. Sadly on some years or packages of car these covers do not open from the outside and if this is the situation we will dedicate a moment on in the second part of this content page to demonstrate the way.
So let’s begin with replacing the number plate bulb by going through the outside of your Chevrolet Avalanche. Whether it’s the front or the back of your automobile the procedure will be the same.
Here are a few simple steps to stick to to carry out this maintenance tasks:
- With the engine off, disconnect the battery terminals from your car
- Face your license plate and use a flat screwdriver or knife to place the flat part into the notch supplied for this purpose (almost always on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Chevrolet Avalanche
- Use your screwdriver or knife to remove the bulb from its place, if you are afraid of damaging anything, you can also do it with your fingers.
- Finally, position the new license plate light bulb
- Last stage, before reassembling, reconnect your battery and verify the light to validate the achievement of the operation.
.
How to replace the number plate bulb on your Chevrolet Avalanche without outside access
Second part of our article, swap this license plate bulb on your Chevrolet Avalanche without external access. In most cases you will be able to access it, but some series (often at the rear does not allow this access).
How to swap the front license plate bulb on my Chevrolet Avalanche
To swap the one on the front plate, nothing could be less hard, you will have to position yourself under the automobile (preferably positioned on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, almost always kept by two soft plastic tabs by pressing on both at once, then now that you have your license plate bulb block in hand, Take out the plastic that works as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (be mindful not to put in too much force otherwise you will break the plastic cover), and you will only have to remove the burnt-out license plate bulb and change it with the new , then check and reassemble the whole thing.
How to swap the rear license plate bulb on my Chevrolet Avalanche
Finally last possibility, you must swap the bulb on the backplate of your Chevrolet Avalanche, but you simply cannot open the cover from the outside of your automobile. In this case, here is the approach to operate this task:
- Disconnect the battery from your Chevrolet Avalanche
- Find the location of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, kept by clips, you will have to lever gently on all the frame of the trunk to remove it.
- Once found, before removing the bulb holders, disconnect the holders for easier access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Replace the burnt-out license plate bulb on your Chevrolet Avalanche, verify it and reassemble it, paying attention to the clips on the trunk liner
.
.
There you have it, you have found out the main tactics for replacing license plate bulbs on your car, be aware that on some models the methodology may be a bit different but you should be able to realize it following the explanation of this content page. If you can’t do it, don’t be reluctant to go to your garage area it would be a shame to break a part of your Chevrolet Avalanche. If you need to change other bulbs like the position light bulbs on your Chevrolet Avalanche or the low beam bulbs on Chevrolet Avalanche, don’t be reluctant to read our content articles which explain you the process to follow.
If you need more guides on the Chevrolet Avalanche, go to our Chevrolet Avalanche category.
