Regardless it’s for your own personal safety, for roadworthiness testing or to avoid a fine, ensuring that your headlamp bulbs are constantly functioning is very important. In fact, bulbs are wearing units that will predictably burn out with time and as a consequence need to be changed. You’re almost certainly on this site because one of your parking lights is burnt out and you’re wondering how to change your Cadillac Escalade’s license plate bulb, we’ve made this article content to help you do it on your own and not have to go to your motor mechanic. Firstly, we will take a look at changing the license plate bulb from the outside, secondly, how to replace the license plate bulb without outside access, and thirdly, how to replace the rear license plate bulb of your Cadillac Escalade.
How to change the license plate bulb on your Cadillac Escalade through the outside
This technique is the quickest of the two, in fact, for this one you will just need to take off the protective covers of the bulbs. Regrettably on some years or packages of car these covers do not open from the outside and if this is the situation we will spend some time on in the second section of this article content to demonstrate the way.
So let’s begin with changing the number plate bulb by going through the outside of your Cadillac Escalade. Regardless it’s the front or the back of your motor vehicle the procedure will be the same.
Here are a few simple actions to stick to to perform this routine service:
- With the engine off, disconnect the battery terminals from your car
- Position yourself in front of your license plate and use a flat screwdriver or knife to place the flat part into the notch specified for this purpose (generally on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Cadillac Escalade
- Use your screwdriver or knife to remove the bulb from its location, in the event that you are worried of destroying something, you can also do it with your fingers.
- Finally, position the new license plate light bulb
- Last step, before reassembling, reconnect your battery and test the light to validate the achievement of the process.
.
How to replace the number plate bulb on your Cadillac Escalade without outside access
Second section of our article, swap this license plate bulb on your Cadillac Escalade without external access. Most often you will be able to access it, however some series (often at the rear does not allow this access).
How to change the front license plate bulb on my Cadillac Escalade
To change the one on the front plate, nothing could be easier, you will have to position yourself under the motor vehicle (preferably put on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, generally kept by two soft plastic tabs by pressing on both simultaneously, then right after you have your license plate bulb block in hand, Remove the plastic that works as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (be mindful not to put in too much pressure or you will break the plastic cover), and you will simply have to take off the burnt-out license plate bulb and replace it with the new , then test out and reassemble the whole thing.
How to change the rear license plate bulb on my Cadillac Escalade
Finally last option, you must change the bulb on the backplate of your Cadillac Escalade, but you cannot really open the cover from the outside of your motor vehicle. In this instance, here is the solution to accomplish this task:
- Unplug the battery from your Cadillac Escalade
- Find the position of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, kept by clips, you will have to lever delicately on all the frame of the trunk to remove it.
- Once found, before removing the bulb holders, disconnect the holders for much easier access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Change the burnt-out license plate bulb on your Cadillac Escalade, test it and reassemble it, watching the clips on the trunk liner
.
.
There you have it, you have discovered the main methods for changing license plate bulbs on your car, take note that on some models the method may be a bit different but you should be able to do it following the outline of this document. If you can’t do it, don’t hesitate to go to your garage it would be a shame to break a part of your Cadillac Escalade. If you want to change other bulbs like the position light bulbs on your Cadillac Escalade or the low beam bulbs on Cadillac Escalade, don’t hesitate to consult our articles which describe you the procedure to follow.
If you want more tutorials on the Cadillac Escalade, go to our Cadillac Escalade category.
