Regardless it’s for your own safety, for roadworthiness testing or to avoid a fine, ensuring your headlamp bulbs are in every case effective is very important. In reality, bulbs are wearing units that will predictably burn out as time passes and therefore need to be changed. You’re likely in this article because one of your parking lights is burnt out and you’re worried about how to change your Buick Envision’s license plate bulb, we’ve written this content to help you do it without any help and not have to go to your motor mechanic. Firstly, we will look at changing the license plate bulb from the outside, secondly, how to change the license plate bulb without outside access, and thirdly, how to change the rear license plate bulb of your Buick Envision.
How to replace the license plate bulb on your Buick Envision coming from the outside
This technique is the fastest of the two, in fact, for this one you will simply need to take away the protective covers of the bulbs. Unfortunately on some years or packages of car these covers do not open from the outside and if this is the situation we will dedicate some time on in the second section of this content to demonstrate the approach.
So let’s start with changing the number plate bulb by going through the outside of your Buick Envision. Regardless it’s the front or the back of your car the technique will be the same.
Here are a few simple actions to follow to perform this maintenance tasks:
- With the engine turned off, disconnect the battery terminals from your car
- Face your license plate and use a flat screwdriver or knife to insert the flat part into the notch assigned for this purpose (in most cases on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Buick Envision
- Use your screwdriver or knife to eject the bulb from its location, if you are afraid of destroying a thing, you can as well do it with your fingers.
- Finally, position the new license plate light bulb
- Last step, before reassembling, reconnect your battery and verify the light to confirm the achievement of the operation.
.
How to replace the number plate bulb on your Buick Envision without outside access
Second section of our content, change this license plate bulb on your Buick Envision without external access. In most cases you will be able to access it, nevertheless some series (often at the rear does not allow this access).
How to replace the front license plate bulb on my Buick Envision
To replace the one on the front plate, nothing could be easier, you will have to position yourself under the car (ideally placed on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, in most cases kept by two soft plastic tabs by pressing on both simultaneously, then right after you have your license plate bulb block in hand, Take off the plastic that acts as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (take extra care not to exert too much force otherwise you will break the plastic cover), and you will only have to take away the burnt-out license plate bulb and change it with the new , then test out and reassemble the whole thing.
How to replace the rear license plate bulb on my Buick Envision
Finally last possibility, you must replace the bulb on the backplate of your Buick Envision, but you simply cannot open the cover from the outside of your car. In this instance, here is the solution to execute this task:
- Unplug the battery from your Buick Envision
- Identify the position of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, kept by clips, you will have to lever carefully on all the frame of the trunk to remove it.
- Once located, before removing the bulb holders, disconnect the holders for less difficult access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Change the burnt-out license plate bulb on your Buick Envision, verify it and reassemble it, paying attention to the clips on the trunk liner
.
.
There you have it, you have found out the main tactics for changing license plate bulbs on your car, be aware that on some models the technique may be a bit different but you should be able to realize it following the outline of this content. If you can’t do it, don’t be reluctant to go to your mechanic it would be a shame to break a part of your Buick Envision. If you desire to change other bulbs like the position light bulbs on your Buick Envision or the low beam bulbs on Buick Envision, don’t be reluctant to browse our content articles which explain you the process to follow.
To find more tips on the Buick Envision, take a look at the Buick Envision category.
