Regardless it’s for your specific security, for roadworthiness tests or to avoid a fine, ensuring your headlamp bulbs are constantly functioning is necessary. In reality, bulbs are wearing units that will inevitably burn out in the future and consequently need to be changed. You’re quite likely on the website because one of your parking lights is burnt out and you’re struggling with how to change your Buick Enclave’s license plate bulb, we’ve written this article to help you do it all on your own and not have to go to your technician. Firstly, we will take a look at changing the license plate bulb from the outside, secondly, how to replace the license plate bulb without outside access, and thirdly, how to replace the rear license plate bulb of your Buick Enclave.
How to replace the license plate bulb on your Buick Enclave throughout the outside
This solution is the most simple of the two, in truth, for this one you will simply require to take out the protective covers of the bulbs. Unfortunately on some years or packages of car these covers do not open from the outside and if this is the case we will spend some time on in the second section of this content to teach you the method.
So let’s start with changing the number plate bulb by going through the outside of your Buick Enclave. Regardless it’s the front or the back of your motor vehicle the procedure will be the same.
Here are a few simple guidelines to follow to conduct this routine service:
- With the engine turned off, disconnect the battery terminals from your car
- Position yourself in front of your license plate and use a flat screwdriver or knife to place the flat part into the notch assigned for this goal (in general on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Buick Enclave
- Use your screwdriver or knife to eject the bulb from its location, in the event that you are scared of breaking a thing, you can also do it with your fingers.
- Finally, put the new license plate light bulb
- Last step, before reassembling, reconnect your battery and verify the light to validate the successfulness of the process.
.
How to change the number plate bulb on your Buick Enclave without outside access
Second section of our content page, change this license plate bulb on your Buick Enclave without external access. In most cases you will be able to access it, however some series (often at the rear does not allow this access).
How to replace the front license plate bulb on my Buick Enclave
To replace the one on the front plate, nothing could be less complicated, you will have to put yourself under the motor vehicle (preferably placed on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, in general kept by two soft plastic tabs by pressing on both simultaneously, then once you have your license plate bulb block in hand, Take off the plastic that works as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (be cautious not to apply too much force or you will break the plastic cover), and you will simply have to take out the burnt-out license plate bulb and replace it with the new , then verify and reassemble the whole thing.
How to replace the rear license plate bulb on my Buick Enclave
Finally last possibility, you must replace the bulb on the backplate of your Buick Enclave, but you simply cannot open the cover from the outside of your motor vehicle. In this case, here is the tactic to do this task:
- Unplug the battery from your Buick Enclave
- Find the position of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, kept by clips, you will have to lever gently on all the frame of the trunk to remove it.
- Once found, before removing the bulb holders, disconnect the holders for much easier access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Replace the burnt-out license plate bulb on your Buick Enclave, verify it and reassemble it, paying attention to the clips on the trunk liner
.
.
There you have it, you have learned the main ways for changing license plate bulbs on your car, take notice that on some models the methodology may be a bit different but you should be able to realize it following the outline of this article content. If you can’t do it, don’t hesitate to go to your workshop it would be a shame to break a part of your Buick Enclave. If you wish to change other bulbs like the position light bulbs on your Buick Enclave or the low beam bulbs on Buick Enclave, don’t hesitate to browse our articles which describe you the operation to follow.
To get more tips on the Buick Enclave, take a look at the Buick Enclave category.
