Whether it’s for your own personal safety, for roadworthiness tests or to avoid a fine, being sure your headlamp bulbs are in every case operational is fundamental. In fact, bulbs are wearing auto parts that will predictably burn out over time and consequently need to be swapped out. You’re most likely in this article because one of your parking lights is burnt out and you’re wanting to know how to change your Buick Cascada’s license plate bulb, we’ve made this content page to help you do it on your own and not have to go to your mechanic. Firstly, we will look at changing the license plate bulb from the outside, secondly, how to replace the license plate bulb without outside access, and thirdly, how to replace the rear license plate bulb of your Buick Cascada.

change-license-plate-bulb-buick-cascada

How to change the license plate bulb on your Buick Cascada coming from the outside

This technique is the fastest of the two, in reality, for this one you will only need to take off the protective covers of the bulbs. Unfortunately on some years or packages of car these covers do not open from the outside and if this is the situation we will dedicate a moment on in the second section of this content page to teach you the way.
So let’s begin with changing the number plate bulb by going through the outside of your Buick Cascada. Whether it’s the front or the back of your motor vehicle the operation will be the same.
Here are a few simple guidelines to follow to perform this maintenance tasks:

  • With the engine off, unplug the battery terminals from your car
  • Position yourself in front of your license plate and use a flat screwdriver or knife to place the flat part into the notch assigned for this goal (in general on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Buick Cascada
  • .

  • Use your screwdriver or knife to remove the bulb from its spot, in the event you are worried of breaking a thing, you can also do it with your fingers.
  • Finally, put the new license plate light bulb
  • Last stage, before reassembling, reconnect your battery and verify the light to confirm the success of the process.

How to change the number plate bulb on your Buick Cascada without outside access

Second section of our article, replace this license plate bulb on your Buick Cascada without external access. Generally you will be able to access it, nevertheless some series (often at the rear does not allow this access).

How to change the front license plate bulb on my Buick Cascada

To change the one on the front plate, nothing could be simpler, you will have to put yourself under the motor vehicle (ideally placed on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, in general kept by two soft plastic tabs by pressing on both simultaneously, then now that you have your license plate bulb block in hand, Remove the plastic that acts as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (be cautious not to put in too much pressure or you will break the plastic cover), and you will simply have to take off the burnt-out license plate bulb and swap it with the new , then verify and reassemble the whole thing.

How to change the rear license plate bulb on my Buick Cascada

Finally last possibility, you must change the bulb on the backplate of your Buick Cascada, but you simply cannot open the cover from the outside of your motor vehicle. In such a case, here is the tactic to execute this task:

  • Unplug the battery from your Buick Cascada
  • Identify the position of your light bulbs from the outside.
  • From the inside of the trunk, you have to remove the lining of the trunk, kept by clips, you will have to lever carefully on all the frame of the trunk to remove it.
  • Once located, before removing the bulb holders, unplug the holders for less difficult access.
  • Using a screwdriver, lever the two plastic parts to remove the bulb holder
  • .

  • Change the burnt-out license plate bulb on your Buick Cascada, verify it and reassemble it, watching the clips on the trunk liner

.
There you have it, you have found out the main tactics for changing license plate bulbs on your car, take notice that on some models the methodology may be a bit different but you should be able to do it following the outline of this document. If you can’t do it, don’t be reluctant to go to your garage area it would be a shame to break a part of your Buick Cascada. If you wish to change other bulbs like the position light bulbs on your Buick Cascada or the low beam bulbs on Buick Cascada, don’t be reluctant to read our articles which explain you the operation to follow.

To find more tips on the Buick Cascada, take a look at the Buick Cascada category.