Regardless whether it’s for your personal security, for roadworthiness tests or to avoid a fine, making sure your headlamp bulbs are all the time effective is very important. In fact, bulbs are wearing units that will surely burn out over time and as a consequence need to be replaced. You’re likely on this site because one of your parking lights is burnt out and you’re wondering how to change your Bmw Serie 4 F32’s license plate bulb, we’ve written this article content to help you do it all on your own and not have to go to your technician. Firstly, we will look at changing the license plate bulb from the outside, secondly, how to change the license plate bulb without outside access, and thirdly, how to change the rear license plate bulb of your Bmw Serie 4 F32.
How to replace the license plate bulb on your Bmw Serie 4 F32 throughout the outside
This process is the simplest of the two, in reality, for this one you will simply require to take off the protective covers of the bulbs. Unfortunately on some years or packages of car these covers do not open from the outside and if this is the case we will dedicate some time on in the second part of this article content to clarify the method.
So let’s start with changing the number plate bulb by going through the outside of your Bmw Serie 4 F32. Regardless whether it’s the front or the back of your automobile the process will be identical.
Here are a few simple guidelines to follow to conduct this service:
- With the engine turned off, unplug the battery terminals from your car
- Position yourself in front of your license plate and use a flat screwdriver or knife to insert the flat part into the notch provided for this intent (almost always on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Bmw Serie 4 F32
- Use your screwdriver or knife to remove the bulb from its placement, in the event you are worried of damaging anything, you can as well do it with your fingers.
- Finally, put the new license plate light bulb
- Last stage, before reassembling, reconnect your battery and test the light to validate the achievement of the procedure.
.
How to change the number plate bulb on your Bmw Serie 4 F32 without outside access
Second part of our document, change this license plate bulb on your Bmw Serie 4 F32 without external access. Most often you will be able to access it, but some series (often at the rear does not allow this access).
How to replace the front license plate bulb on my Bmw Serie 4 F32
To replace the one on the front plate, nothing could be less difficult, you will have to put yourself under the automobile (ideally put on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, almost always held by two soft plastic tabs by pressing on both at the same time, then once you have your license plate bulb block in hand, Remove the plastic that operates as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (be cautious not to put in too much pressure otherwise you will break the plastic cover), and you will just have to take off the burnt-out license plate bulb and replace it with the new , then test out and reassemble the whole thing.
How to replace the rear license plate bulb on my Bmw Serie 4 F32
Finally last option, you must replace the bulb on the backplate of your Bmw Serie 4 F32, but you cannot open the cover from the outside of your automobile. In such a case, here is the method to do this operation:
- Disconnect the battery from your Bmw Serie 4 F32
- Locate the spot of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, held by clips, you will have to lever carefully on all the frame of the trunk to remove it.
- Once established, before removing the bulb holders, unplug the holders for much easier access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Change the burnt-out license plate bulb on your Bmw Serie 4 F32, test it and reassemble it, paying attention to the clips on the trunk liner
.
.
There you have it, you have discovered the main tactics for changing license plate bulbs on your car, take notice that on some models the method may be a bit different but you should be able to realize it following the explanation of this article content. If you can’t do it, don’t hesitate to go to your garage it would be a shame to break a part of your Bmw Serie 4 F32. If you want to change other bulbs like the position light bulbs on your Bmw Serie 4 F32 or the low beam bulbs on Bmw Serie 4 F32, don’t hesitate to browse our content articles which demonstrate you the process to follow.
To discover more tips on the Bmw Serie 4 F32, take a look at the Bmw Serie 4 F32 category.
