It doesn’t matter if it’s for your own security, for roadworthiness tests or to avoid a fine, being sure your headlamp bulbs are in every case operational is fundamental. Indeed, bulbs are wearing units that will predictably burn out after awhile and therefore need to be changed. You’re likely on this website because one of your parking lights is burnt out and you’re struggling with how to change your Bmw Serie 2 F23’s license plate bulb, we’ve written this document to help you do it by yourself and not have to go to your motor mechanic. Firstly, we will look at changing the license plate bulb from the outside, secondly, how to replace the license plate bulb without outside access, and thirdly, how to replace the rear license plate bulb of your Bmw Serie 2 F23.
How to replace the license plate bulb on your Bmw Serie 2 F23 coming from the outside
This solution is the least difficult of the two, in truth, for this one you will simply need to take out the protective covers of the bulbs. Unfortunately on some years or packages of car these covers do not open from the outside and if this is the case we will spend some time on in the second part of this article content to describe the method.
So let’s begin with replacing the number plate bulb by going through the outside of your Bmw Serie 2 F23. It doesn’t matter if it’s the front or the back of your car the procedure will be the same.
Here are a few simple steps to stick to to perform this service:
- With the engine turned off, unplug the battery terminals from your car
- Position yourself in front of your license plate and use a flat screwdriver or knife to insert the flat part into the notch specified for this intent (in general on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Bmw Serie 2 F23
- Use your screwdriver or knife to eject the bulb from its placement, if you are scared of destroying something, you can as well do it with your fingers.
- Finally, put the new license plate light bulb
- Last step, before reassembling, reconnect your battery and verify the light to validate the successfulness of the procedure.
.
How to change the number plate bulb on your Bmw Serie 2 F23 without outside access
Second part of our content, replace this license plate bulb on your Bmw Serie 2 F23 without external access. Most often you will be able to access it, however some series (often at the rear does not allow this access).
How to replace the front license plate bulb on my Bmw Serie 2 F23
To replace the one on the front plate, nothing could be much easier, you will have to put yourself under the car (ideally positioned on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, in general held by two soft plastic tabs by pressing on both at the same time, then right after you have your license plate bulb block in hand, Take away the plastic that operates as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (take extra care not to exert too much force otherwise you will break the plastic cover), and you will simply have to take out the burnt-out license plate bulb and change it with the new , then test out and reassemble the whole thing.
How to replace the rear license plate bulb on my Bmw Serie 2 F23
Finally last option, you must replace the bulb on the backplate of your Bmw Serie 2 F23, but you simply cannot open the cover from the outside of your car. In this instance, here is the approach to operate this task:
- Unplug the battery from your Bmw Serie 2 F23
- Find the location of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, held by clips, you will have to lever carefully on all the frame of the trunk to remove it.
- Once established, before removing the bulb holders, unplug the holders for much easier access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Replace the burnt-out license plate bulb on your Bmw Serie 2 F23, verify it and reassemble it, watching the clips on the trunk liner
.
.
There you have it, you have discovered the main tactics for replacing license plate bulbs on your car, bear in mind that on some models the methodology may be a bit different but you should be able to realize it following the outline of this article. If you can’t do it, don’t hesitate to go to your garage area it would be a shame to break a part of your Bmw Serie 2 F23. If you wish to change other bulbs like the position light bulbs on your Bmw Serie 2 F23 or the low beam bulbs on Bmw Serie 2 F23, don’t hesitate to consult our content articles which demonstrate you the operation to follow.
If perhaps you have any additional questions about the Bmw Serie 2 F23, do not hesitate to consult our Bmw Serie 2 F23 category.
