Regardless it’s for your own safety, for roadworthiness tests or to avoid a fine, ensuring that your headlamp bulbs are always operational is really important. In fact, bulbs are wearing units that will undoubtedly burn out with time and therefore need to be replaced. You’re likely on the website because one of your parking lights is burnt out and you’re worried about how to change your Bmw Serie 1 F20’s license plate bulb, we’ve made this article content to help you do it without any help and not have to go to your auto mechanic. Firstly, we will look at changing the license plate bulb from the outside, secondly, how to replace the license plate bulb without outside access, and thirdly, how to replace the rear license plate bulb of your Bmw Serie 1 F20.

change-license-plate-bulb-bmw-serie-1-f20

How to change the license plate bulb on your Bmw Serie 1 F20 throughout the outside

This approach is the quickest of the two, in fact, for this one you will just require to take out the protective covers of the bulbs. Regrettably on some years or packages of car these covers do not open from the outside and if this is the case we will dedicate some time on in the second part of this content page to clarify the way.
So let’s start with replacing the number plate bulb by going through the outside of your Bmw Serie 1 F20. Regardless it’s the front or the back of your automobile the method will be similar.
Here are a few simple steps to stick to to execute this routine service:

  • With the engine off, disconnect the battery terminals from your car
  • Position yourself in front of your license plate and use a flat screwdriver or knife to place the flat part into the notch specified for this goal (in most cases on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Bmw Serie 1 F20
  • .

  • Use your screwdriver or knife to remove the bulb from its place, in the event that you are worried of destroying a thing, you can also do it with your fingers.
  • Finally, position the new license plate light bulb
  • Last step, before reassembling, reconnect your battery and check the light to validate the achievement of the task.

How to change the number plate bulb on your Bmw Serie 1 F20 without outside access

Second part of our item, replace this license plate bulb on your Bmw Serie 1 F20 without external access. In most cases you will be able to access it, however some series (often at the rear does not allow this access).

How to change the front license plate bulb on my Bmw Serie 1 F20

To change the one on the front plate, nothing could be much easier, you will have to position yourself under the automobile (ideally placed on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, in most cases held by two soft plastic tabs by pressing on both at once, then right after you have your license plate bulb block in hand, Remove the plastic that works as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (be attentive not to exert too much force otherwise you will break the plastic cover), and you will just have to take out the burnt-out license plate bulb and swap it with the new , then verify and reassemble the whole thing.

How to change the rear license plate bulb on my Bmw Serie 1 F20

Finally last option, you must change the bulb on the backplate of your Bmw Serie 1 F20, but you are not able to open the cover from the outside of your automobile. In such a case, here is the process to operate this task:

  • Disconnect the battery from your Bmw Serie 1 F20
  • Identify the spot of your light bulbs from the outside.
  • From the inside of the trunk, you have to remove the lining of the trunk, held by clips, you will have to lever delicately on all the frame of the trunk to remove it.
  • Once found, before removing the bulb holders, disconnect the holders for much easier access.
  • Using a screwdriver, lever the two plastic parts to remove the bulb holder
  • .

  • Change the burnt-out license plate bulb on your Bmw Serie 1 F20, check it and reassemble it, paying attention to the clips on the trunk liner

.
There you have it, you have learned the main ways for replacing license plate bulbs on your car, take note that on some models the method may be a bit different but you should be able to do it following the explanation of this document. If you can’t do it, don’t hesitate to go to your workshop it would be a shame to break a part of your Bmw Serie 1 F20. If you need to change other bulbs like the position light bulbs on your Bmw Serie 1 F20 or the low beam bulbs on Bmw Serie 1 F20, don’t hesitate to read our articles which demonstrate you the process to follow.

To discover more tips on the Bmw Serie 1 F20, take a look at the Bmw Serie 1 F20 category.