Whether it’s for your specific security, for roadworthiness tests or to avoid a fine, making sure your headlamp bulbs are all the time effective is fundamental. In reality, bulbs are wearing auto parts that will inevitably burn out in the future and as a consequence need to be swapped out. You’re almost certainly on this website because one of your parking lights is burnt out and you’re struggling with how to change your Audi Rs6’s license plate bulb, we’ve created this article to help you do it all on your own and not have to go to your technician. Firstly, we will examine changing the license plate bulb from the outside, secondly, how to replace the license plate bulb without outside access, and thirdly, how to replace the rear license plate bulb of your Audi Rs6.
How to change the license plate bulb on your Audi Rs6 throughout the outside
This method is the most simple of the two, in reality, for this one you will just need to take off the protective covers of the bulbs. Sadly on some years or packages of car these covers do not open from the outside and if this is the case we will dedicate some time on in the second part of this article to explain the approach.
So let’s start with swapping the number plate bulb by going through the outside of your Audi Rs6. Whether it’s the front or the back of your car the process will be identical.
Here are a few simple steps to follow to conduct this routine service:
- With the engine turned off, unplug the battery terminals from your car
- Position yourself in front of your license plate and use a flat screwdriver or knife to place the flat part into the notch specified for this purpose (in most cases on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Audi Rs6
- Use your screwdriver or knife to eject the bulb from its location, in the event you are afraid of destroying anything, you can as well do it with your fingers.
- Finally, position the new license plate light bulb
- Last step, before reassembling, reconnect your battery and test the light to validate the success of the task.
.
How to change the number plate bulb on your Audi Rs6 without outside access
Second part of our item, swap this license plate bulb on your Audi Rs6 without external access. Most often you will be able to access it, nevertheless some series (often at the rear does not allow this access).
How to change the front license plate bulb on my Audi Rs6
To change the one on the front plate, nothing could be less hard, you will have to position yourself under the car (ideally positioned on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, in most cases kept by two soft plastic tabs by pressing on both at once, then once you have your license plate bulb block in hand, Take away the plastic that acts as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (be attentive not to put in too much pressure or you will break the plastic cover), and you will only have to take off the burnt-out license plate bulb and swap it with the new , then test and reassemble the whole thing.
How to change the rear license plate bulb on my Audi Rs6
Finally last possibility, you must change the bulb on the backplate of your Audi Rs6, but you are not able to open the cover from the outside of your car. In this case, here is the technique to do this operation:
- Disconnect the battery from your Audi Rs6
- Identify the spot of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, kept by clips, you will have to lever softly on all the frame of the trunk to remove it.
- Once located, before removing the bulb holders, unplug the holders for less difficult access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Replace the burnt-out license plate bulb on your Audi Rs6, test it and reassemble it, paying attention to the clips on the trunk liner
.
.
There you have it, you have found out the main techniques for swapping license plate bulbs on your car, bear in mind that on some models the method may be a bit different but you should be able to accomplish it following the outline of this document. If you can’t do it, don’t hesitate to go to your garage it would be a shame to break a part of your Audi Rs6. If you need to change other bulbs like the position light bulbs on your Audi Rs6 or the low beam bulbs on Audi Rs6, don’t hesitate to browse our content articles which explain you the operation to follow.
Whenever you have any further questions about the Audi Rs6, do not hesitate to consult our Audi Rs6 category.
