It doesn’t matter if it’s for your own safety, for roadworthiness testing or to avoid a fine, being sure your headlamp bulbs are all the time operational is really important. In reality, bulbs are wearing units that will surely burn out after some time and as a consequence need to be replaced. You’re likely on this website because one of your parking lights is burnt out and you’re struggling with how to change your Audi Q3’s license plate bulb, we’ve written and published this content page to help you do it without any help and not have to go to your technician. Firstly, we will look at changing the license plate bulb from the outside, secondly, how to change the license plate bulb without outside access, and thirdly, how to change the rear license plate bulb of your Audi Q3.
How to swap the license plate bulb on your Audi Q3 throughout the outside
This process is the most simple of the two, actually, for this one you will just need to take out the protective covers of the bulbs. Sadly on some years or packages of car these covers do not open from the outside and if this is the case we will spend some time on in the second part of this article content to teach you the method.
So let’s begin with changing the number plate bulb by going through the outside of your Audi Q3. It doesn’t matter if it’s the front or the back of your automobile the technique will be identical.
Here are a few simple steps to follow to carry out this routine service:
- With the engine turned off, unplug the battery terminals from your car
- Position yourself in front of your license plate and use a flat screwdriver or knife to insert the flat part into the notch supplied for this purpose (usually on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Audi Q3
- Use your screwdriver or knife to remove the bulb from its placement, if you are afraid of breaking something, you can also do it with your fingers.
- Finally, position the new license plate light bulb
- Last stage, before reassembling, reconnect your battery and test the light to validate the achievement of the operation.
.
How to replace the number plate bulb on your Audi Q3 without outside access
Second part of our document, change this license plate bulb on your Audi Q3 without external access. Generally you will be able to access it, however some series (often at the rear does not allow this access).
How to swap the front license plate bulb on my Audi Q3
To swap the one on the front plate, nothing could be simpler, you will have to position yourself under the automobile (ideally put on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, usually held by two soft plastic tabs by pressing on both at the same time, then once you have your license plate bulb block in hand, Remove the plastic that operates as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (be attentive not to exert too much pressure otherwise you will break the plastic cover), and you will only have to take out the burnt-out license plate bulb and replace it with the new , then check and reassemble the whole thing.
How to swap the rear license plate bulb on my Audi Q3
Finally last solution, you must swap the bulb on the backplate of your Audi Q3, but you simply cannot open the cover from the outside of your automobile. In such a case, here is the solution to perform this task:
- Disconnect the battery from your Audi Q3
- Find the spot of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, held by clips, you will have to lever softly on all the frame of the trunk to remove it.
- Once located, before removing the bulb holders, unplug the holders for easier access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Change the burnt-out license plate bulb on your Audi Q3, test it and reassemble it, watching the clips on the trunk liner
.
.
There you have it, you have discovered the main tactics for changing license plate bulbs on your car, bear in mind that on some models the technique may be a bit different but you should be able to accomplish it following the explanation of this document. If you can’t do it, don’t hesitate to go to your garage it would be a shame to break a part of your Audi Q3. If you need to change other bulbs like the position light bulbs on your Audi Q3 or the low beam bulbs on Audi Q3, don’t hesitate to consult our content articles which demonstrate you the process to follow.
If you wish more guides on the Audi Q3, go to our Audi Q3 category.
