Regardless it’s for your specific safety, for roadworthiness testing or to avoid a fine, ensuring that your headlamp bulbs are constantly operational is necessary. In fact, bulbs are wearing auto parts that will inevitably burn out as time passes and as a consequence need to be replaced. You’re quite likely on the website because one of your parking lights is burnt out and you’re worried about how to change your Audi A3’s license plate bulb, we’ve created this article to help you do it on your own and not have to go to your mechanic. Firstly, we will take a look at changing the license plate bulb from the outside, secondly, how to change the license plate bulb without outside access, and thirdly, how to change the rear license plate bulb of your Audi A3.
How to replace the license plate bulb on your Audi A3 throughout the outside
This tactic is the quickest of the two, in reality, for this one you will just need to take away the protective covers of the bulbs. Sadly on some years or packages of car these covers do not open from the outside and if this is the situation we will spend some time on in the second section of this document to show you the approach.
So let’s start with replacing the number plate bulb by going through the outside of your Audi A3. Regardless it’s the front or the back of your car the procedure will be similar.
Here are a few simple steps to follow to perform this maintenance tasks:
- With the engine off, disconnect the battery terminals from your car
- Position yourself in front of your license plate and use a flat screwdriver or knife to place the flat part into the notch provided for this intent (in most cases on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Audi A3
- Use your screwdriver or knife to eject the bulb from its location, in the event you are afraid of destroying something, you can also do it with your fingers.
- Finally, position the new license plate light bulb
- Last stage, before reassembling, reconnect your battery and test the light to validate the successfulness of the operation.
.
How to replace the number plate bulb on your Audi A3 without outside access
Second section of our item, replace this license plate bulb on your Audi A3 without external access. Generally you will be able to access it, nevertheless some series (often at the rear does not allow this access).
How to replace the front license plate bulb on my Audi A3
To replace the one on the front plate, nothing could be much easier, you will have to position yourself under the car (ideally positioned on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, in most cases held by two soft plastic tabs by pressing on both at the same time, then right after you have your license plate bulb block in hand, Take away the plastic that works as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (be cautious not to exert too much force or you will break the plastic cover), and you will simply have to take away the burnt-out license plate bulb and swap it with the new , then check and reassemble the whole thing.
How to replace the rear license plate bulb on my Audi A3
Finally last solution, you must replace the bulb on the backplate of your Audi A3, but you are not able to open the cover from the outside of your car. In this instance, here is the tactic to do this task:
- Unplug the battery from your Audi A3
- Find the position of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, held by clips, you will have to lever delicately on all the frame of the trunk to remove it.
- Once established, before removing the bulb holders, disconnect the holders for easier access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Replace the burnt-out license plate bulb on your Audi A3, test it and reassemble it, paying attention to the clips on the trunk liner
.
.
There you have it, you have learned the main ways for replacing license plate bulbs on your car, be aware that on some models the methodology may be a bit different but you should be able to realize it following the explanation of this content. If you can’t do it, don’t hesitate to go to your garage it would be a shame to break a part of your Audi A3. If you need to change other bulbs like the position light bulbs on your Audi A3 or the low beam bulbs on Audi A3, don’t hesitate to read our content articles which explain you the operation to follow.
To find more tips on the Audi A3, take a look at the Audi A3 category.
