It doesn’t matter if it’s for your specific safety, for roadworthiness tests or to avoid a fine, making sure your headlamp bulbs are always functional is extremely important. In fact, bulbs are wearing parts that will predictably burn out after some time and therefore need to be changed. You’re most certainly in this article because one of your parking lights is burnt out and you’re wanting to know how to change your Acura RDX’s license plate bulb, we’ve made this content to help you do it on your own and not have to go to your auto technician. Firstly, we will look at changing the license plate bulb from the outside, secondly, how to replace the license plate bulb without outside access, and thirdly, how to replace the rear license plate bulb of your Acura RDX.
How to change the license plate bulb on your Acura RDX coming from the outside
This tactic is the easiest of the two, in fact, for this one you will just have to take out the protective covers of the bulbs. Regrettably on some years or packages of car these covers do not open from the outside and if this is the situation we will dedicate some time on in the second part of this document to demonstrate the approach.
So let’s start with swapping the number plate bulb by going through the outside of your Acura RDX. It doesn’t matter if it’s the front or the back of your motor vehicle the process will be identical.
Here are a few simple actions to stick to to carry out this routine service:
- With the engine turned off, unplug the battery terminals from your car
- Position yourself in front of your license plate and use a flat screwdriver or knife to place the flat part into the notch specified for this intent (in most cases on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Acura RDX
- Use your screwdriver or knife to eject the bulb from its spot, if you are worried of destroying anything, you can as well do it with your fingers.
- Finally, put the new license plate light bulb
- Last stage, before reassembling, reconnect your battery and verify the light to confirm the successfulness of the task.
.
How to change the number plate bulb on your Acura RDX without outside access
Second part of our content, replace this license plate bulb on your Acura RDX without external access. Generally you will be able to access it, however some series (often at the rear does not allow this access).
How to change the front license plate bulb on my Acura RDX
To change the one on the front plate, nothing could be simpler, you will have to put yourself under the motor vehicle (preferably positioned on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, in most cases held by two soft plastic tabs by pressing on both at once, then once you have your license plate bulb block in hand, Take away the plastic that acts as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (be attentive not to put in too much force or you will break the plastic cover), and you will only have to take out the burnt-out license plate bulb and swap it with the new , then check and reassemble the whole thing.
How to change the rear license plate bulb on my Acura RDX
Finally last option, you must change the bulb on the backplate of your Acura RDX, but you are not able to open the cover from the outside of your motor vehicle. In this case, here is the technique to perform this operation:
- Unplug the battery from your Acura RDX
- Identify the location of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, held by clips, you will have to lever softly on all the frame of the trunk to remove it.
- Once found, before removing the bulb holders, unplug the holders for less complicated access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Replace the burnt-out license plate bulb on your Acura RDX, verify it and reassemble it, watching the clips on the trunk liner
.
.
There you have it, you have found out the main tactics for swapping license plate bulbs on your car, take note that on some models the technique may be a bit different but you should be able to accomplish it following the explanation of this article content. If you can’t do it, don’t hesitate to go to your garage area it would be a shame to break a part of your Acura RDX. If you want to change other bulbs like the position light bulbs on your Acura RDX or the low beam bulbs on Acura RDX, don’t hesitate to consult our articles which describe you the procedure to follow.
If you want more guides on the Acura RDX, go to our Acura RDX category.
