If you experience you can’t see as well at night, or you experience you’re lighting too low, or too high, in all these cases, there’s only one part of your vehicle to blame – your headlights, also identified as high beams. Nevertheless this adjustment may seem easy thanks to the thumbwheel on your dashboard, a whole adjustment is much more complex than this basic manipulation, and in this post, we are going to see how to adjust the headlights of your Volkswagen Crafter? To get this done, first we will see why you need to adjust your high beams, and secondly how to adjust the headlights of your Volkswagen Crafter.
Why adjust the headlights of your Volkswagen Crafter?
So let’s start our article with the benefit of adjusting the headlights of your Volkswagen Crafter. For many of us, our headlights are adjusted good enough, and they seem to light up enough after dark. Regrettably this is not always the case and examining this setting, either because the headlights on your Volkswagen Crafter are not bright enough, or because you have the feeling that they are too weak is a good idea .
Adjusting the high beams of your Volkswagen Crafter for safety
To begin with, the headlight adjustment of a Volkswagen Crafter must be finished for a very easy security motive. Whether it’s for you, or for the other users you come across during your night trips. Obviously, if you don’t see enough, the risk is to ignore an obstacle on your way, or to anticipate a curve badly. On the other hand, if your headlights are too strong, regardless if you are meant to switch to low beam lights when you pass a vehicle, the time required to make this switch will generally expose the driver in front of you to the headlight beam of your Volkswagen Crafter . It is therefore important for others as well as for you to have an ideal adjustment of your headlights.
Adjusting the headlights of a Volkswagen Crafter for legal reasons
Furthermore to security, there is a law that regulates the power, the adjustment of motor vehicle headlights (articles R313-2 of the Highway Code), here is what it specifies: have between 2 and 4 headlights that illuminate at minimum 100 meters. Another legislation regulates their use, the European one (directive 76/756/EEC), which stipulates that there is no maximum height for the adjustment of the headlights, but that the maximum width of the beam must be very same to that of the dipped headlights and that the maximum luminosity must be 225, 000 cd.
How to adjust the headlights of a Volkswagen Crafter?
We will now proceed to the section that concerns you the most in this post, how to adjust the headlights of his Volkswagen Crafter? This setting may seem a bit difficult, but by following the guidelines you should have the ability to do it without too much problem.
Preparations to adjust the headlights of a Volkswagen Crafter
To begin with, you’ll need to prepare your vehicle to adjust your high beams in good conditions, here are the preparations to executed:
- Place your vehicle on a surface in front of a white wall for example, about 4 or 5 meters from the wall.
- Check your tire pressure carefully.
- Check that the height adjustment knob for the lights is set to 0
- Try doing that with half a full tank.
- Take out all needless weight from the car, just one person should be in the driver’s seat.
.
The headlight adjustment of his Volkswagen Crafter
Once your car is in place, you will turn on your dipped beam and make a cross-shaped mark (one horizontal and one vertical section) in the middle of the beam that will be projected on the wall. Check with a level that both parts of the cross are straight. Then back your vehicle up to a distance of between 7 and 10 metres. For the rest of the procedure here are the steps to stick to:
- Open your hood, identify the screws for horizontal and vertical modification of the headlights of your Volkswagen Crafter (they are generally designated, and those on top must adjust the verticality and the one on the side manages the horizontality of the adjustment).
- Use a cloth or another thing to hide the projector on which you are not making the correction.
- Using the screws to make the horizontal correction, you should have the most intense part of the beam which should be a little to the right of the vertical line marked on the wall
- With regard to vertical correction, you will have to use the screw to try to position the upper end of the beam at the level of the horizontal marking on the wall, or slightly down below.
- Once finished, verify that the headlights setting of your Volkswagen Crafter is coherent, do not hesitate to verify it after you have driven it, oftentimes it may move.
.
.
If you want to adjust the fog lights on your Volkswagen Crafter, please read our article on this subject.
If perhaps you have any further questions about the Volkswagen Crafter, do not hesitate to consult our Volkswagen Crafter category.
