Whether you experience you can’t see as well at night, or you experience you’re lighting too low, or too high, in all these situations, there’s only one component of your car to take responsibility – your headlights, as well identified as high beams. Nevertheless this adjustment might seem easy thanks to the thumbwheel on your dashboard, a whole adjustment is much more technical than this elementary manipulation, and in this article, we are going to see how to adjust the headlights of your Renualt Express? To achieve this, first we will see why you need to adjust your high beams, and secondly how to adjust the headlights of your Renualt Express.
Why adjust the headlights of your Renualt Express?
So let’s begin our article with the interest of adjusting the headlights of your Renualt Express. For many of us, our headlights are adjusted well enough, and they appear to light up enough through the night. Sadly this is not always the circumstance and looking at this setting, either because the headlights on your Renualt Express are not bright enough, or because you have the impression that they are too weak is a good idea .
Adjusting the high beams of your Renualt Express for safety
First of all, the headlight adjustment of a Renualt Express must be finished for a very easy security explanation. Regardless it’s for you, or for the other users you come across during your night trips. Indeed, if you don’t see enough, the risk is to miss out an obstacle on the road, or to anticipate a curve badly. However, if your headlights are too powerful, even if you are supposed to switch to low beam lights when you pass a vehicle, the time required to make this change will most of the time expose the driver in front of you to the headlight beam of your Renualt Express . It is therefore important for others as well as for you to have an optimal adjustment of your headlights.
Adjusting the headlights of a Renualt Express for legal reasons
In addition to security, there is a law that regulates the power, the adjustment of motor vehicle headlights (articles R313-2 of the Highway Code), here is what it specifies: have between 2 and 4 headlights that illuminate at least 100 meters. Another legislation regulates their use, the European one (directive 76/756/EEC), which stipulates that there is no maximum height for the adjustment of the headlights, but that the maximum width of the beam must be very same to that of the dipped headlights and that the maximum luminosity must be 225, 000 cd.
How to adjust the headlights of a Renualt Express?
We will now move on to the part that interests you the most in this article, how to adjust the headlights of his Renualt Express? This adjustment might seem a bit difficult, but by following the guidance you should be able to perform it without too much issue.
Preparations to adjust the headlights of a Renualt Express
First of all, you’ll need to prepare your car to adjust your high beams in good conditions, here are the preparations to set up:
- Place your car on a surface in front of a white wall for example, about 4 or 5 meters from the wall.
- Check your tire pressure attentively.
- Check that the height adjustment knob for the lights is set to 0
- Try doing that with half a full tank.
- Take out all unnecessary weight from the vehicle, only one person should be in the driver’s seat.
.
The headlight adjustment of his Renualt Express
Once your car is in position, you will turn on your dipped beam and make a cross-shaped mark (one horizontal and one vertical section) in the middle of the beam that will be projected on the wall. Check with a level that both parts of the cross are straight. Then back your car up to a distance of between 7 and 10 metres. For the rest of the process here are the steps to stick to:
- Open your bonnet, find the screws for horizontal and vertical adjustment of the headlights of your Renualt Express (they are in most cases designated, and those on top must adjust the verticality and the one on the side handles the horizontality of the adjustment).
- Use a cloth or another thing to hide the projector on which you are not making the correction.
- Using the screws to make the horizontal correction, you should have the most intense component of the beam which should be a little to the right of the vertical line marked on the wall
- With regard to vertical correction, you will have to use the screw to try to position the upper end of the beam at the level of the horizontal marking on the wall, or slightly down below.
- Once finished, check that the headlights setting of your Renualt Express is coherent, do not hesitate to check it after you have driven it, occasionally it may move.
.
.
If you want to adjust the fog lights on your Renualt Express, please go through our article on this subject matter.
To find more tips on the Renualt Express, take a look at the Renualt Express category.
