If you experience you can’t see as well at night, or you experience you’re lighting too low, or too high, in all these cases, there’s only one component of your car to blame – your headlights, as well called high beams. Although this adjustment might seem easy thanks to the thumbwheel on your dashboard, a whole adjustment is much more complex than this elementary manipulation, and in this post, we are going to see how to adjust the headlights of your Chrysler Sebring? To do this, first we will see why you need to adjust your high beams, and secondly how to adjust the headlights of your Chrysler Sebring.
Why adjust the headlights of your Chrysler Sebring?
So let’s begin our content with the interest of adjusting the headlights of your Chrysler Sebring. For most people, our headlights are adjusted sufficiently, and they seem to light up enough at nighttime. Sadly this is not always the circumstance and looking at this setting, either because the headlights on your Chrysler Sebring are not bright enough, or because you have the sensation that they are too weak is a wise decision .
Adjusting the high beams of your Chrysler Sebring for safety
To begin with, the headlight adjustment of a Chrysler Sebring must be achieved for a basic safety explanation. Regardless it’s for you, or for the other users you come across during your night trips. In actual fact, if you don’t see enough, the risk is to miss out an obstacle on the road, or to anticipate a curve badly. However, if your headlights are too powerful, regardless if you are expected to switch to low beam lights when you cross a vehicle, the time required to make this switch will generally expose the driver in front of you to the headlight beam of your Chrysler Sebring . It is therefore important for others as well as for you to have an ideal adjustment of your headlights.
Adjusting the headlights of a Chrysler Sebring for legal reasons
Furthermore to safety, there is a law that supervises the power, the adjustment of motor vehicle headlights (articles R313-2 of the Highway Code), here is what it specifies: have between 2 and 4 headlights that illuminate at minimum 100 meters. Another legislation supervises their use, the European one (directive 76/756/EEC), which stipulates that there is no maximum height for the adjustment of the headlights, but that the maximum width of the beam must be very same to that of the dipped headlights and that the maximum luminosity must be 225, 000 cd.
How to adjust the headlights of a Chrysler Sebring?
We will now proceed to the part that interests you the most in this post, how to adjust the headlights of his Chrysler Sebring? This setting might seem a bit complex, but by following the guidelines you should be able to complete it without too much issue.
Preparations to adjust the headlights of a Chrysler Sebring
To begin with, you’ll need to prepare your car to adjust your high beams in good conditions, here are the preparations to put in place:
- Place your car on a surface in front of a white wall for example, about 4 or 5 meters from the wall.
- Verify your tire pressure cautiously.
- Verify that the height adjustment knob for the lights is set to 0
- Try doing that with half a full tank.
- Remove all unnecessary weight from the automobile, just one person should be in the driver’s seat.
.
The headlight adjustment of his Chrysler Sebring
Once your car is in place, you will turn on your dipped beam and make a cross-shaped mark (one horizontal and one vertical section) in the middle of the beam that will be projected on the wall. Verify with a level that both parts of the cross are horizontal. Then back your car up to a distance of between 7 and 10 metres. For the rest of the procedure here are the steps to follow:
- Open your hood, find the screws for horizontal and vertical modification of the headlights of your Chrysler Sebring (they are in most cases marked, and those on top must modify the verticality and the one on the side manages the horizontality of the adjustment).
- Use a cloth or different things to hide the projector on which you are not making the adjustment.
- Using the screws to make the horizontal adjustment, you should have the most intense component of the beam which should be a little to the right of the vertical line noted on the wall
- With regard to vertical adjustment, you will have to use the screw to try to position the upper end of the beam at the level of the horizontal marking on the wall, or slightly down below.
- Once finished, verify that the headlights setting of your Chrysler Sebring is logical, do not think twice to verify it after you have driven it, sometimes it may move.
.
.
If you want to adjust the fog lights on your Chrysler Sebring, please go through our content on this subject matter.
If you want more tutorials on the Chrysler Sebring, go to our Chrysler Sebring category.
