It doesn’t matter if you feel you can’t see properly during the night, whether you feel you’re lighting too low or too high, in all of these cases, there’s only one part of your vehicle to blame – your low beams. Despite the fact this adjustment may seem to be easy to do thanks to the thumbwheel on your dashboard, a complete adjustment is much more complicated than this ordinary modification, and in this content page, we will discover how to adjust the low beam lights of your Subaru Outback? For this, first of all we will discover why you should adjust your lights, and, secondly, how to adjust the low beam lights of your Subaru Outback.


Why adjust the low beam lights of your Subaru Outback?

So let’s commence our content page with the point of adjusting the low beam lights of your Subaru Outback. For a lot of people these lights are good enough adjusted, and it looks like that they light up enough at night. However this is not necessarily the case and verifying this setting, either because the low beams of your Subaru Outback are not lighting up well, or because you have the sense that they are too low or too strong is a good idea .

Adjusting the low beam of your Subaru Outback for security is a good idea.

To start, the adjusting of the dipped headlights of an Subaru Outback must be done for a basic security cause. Whether it’s for you, or for the other drivers you come across during your night journeys. In fact, if you don’t see enough, the real danger is to miss an obstacle on the route, or to anticipate a curve badly. In contrast, if your lights are too strong, you risk dazzling the car owners in front of you, and thus putting yourself at risk. It is consequently imperative for others as well as for you to have an optimal setting of your parking lights.

Setting the low beam headlights of an Subaru Outback for law motives

Furthermore to security, there is a law that supervises the power, the adjustment of low beams of cars, here is what it specifies: have between 2 and 4 headlights that illuminate at minimum , 30 meters. Another legislation supervises their use, the European one (directive 76/756/EEC), which stipulates that the height of the beam must be between 500 mm and 1200 mm from the floor, and that they must be at least 600 mm apart.

How to adjust the low-beam headlamps of a Subaru Outback?

We will now go forward to the part that interests you the more in this content page, how to adjust the low beams of his Subaru Outback? This setting may sound a bit difficult, but if you stick to the recommendations you should be able to do it without too much issue.

Preparations to set the low beam of a Subaru Outback

To start, you will need to prepare your vehicle to adjust your low beam lights in good conditions, here are the preparations to put in place:

  • Place your vehicle on a floor in front of a white wall for example, about 4 or 5 meters from the wall.
  • Verify your tire pressure carefully.
  • Verify that the height adjustment knob for the lights is set to 0
  • .

  • Try doing that with half a full tank.
  • Remove all needless weight from the vehicle, only one person should be in the driver’s seat.

The setting of the low beam headlights of his Subaru Outback

Once your vehicle is in position, you will switch on your dipped beam and make a cross-shaped mark (one horizontal and one vertical section) in the middle of the beam that will be projected on the wall. Make sure with a level that both parts of the cross are straight. Then step back your vehicle up to a distance of between 7 and 10 metres. For the rest of the procedure here are the basic steps to stick to:

  • Open your bonnet, situate the screws for horizontal and vertical adjustment of the lights of your Subaru Outback (they are commonly marked, and those above must adjust the verticality and those on the side controls the horizontality of the adjustment).
  • Use a cloth or something else to hide the light on which you are not making the adjustment.
  • Using the screws to make the horizontal adjustment, you should have the most intense part of the beam which should be a little to the right of the vertical line marked on the wall
  • .

  • With regard to vertical adjustment, you will have to use the screw to try to position the upper end of the beam at the level of the horizontal marking on the wall, or slightly below.
  • Once complete, examine that the low beam setting of your Subaru Outback is consistent on the road, do not be reluctant to examine that it has been driven, in some cases it may move.

If you want to adjust the fog lights on your Subaru Outback, please go through our content page on this subject.

To find more tips on the Subaru Outback, take a look at the Subaru Outback category.