It doesn’t matter if you feel you can’t see good enough during the night, regardless whether you feel you’re lighting too low or too high, in all of these situations, there’s only one component of your motor vehicle to blame – your low beams. Even though this correction may seem easy thanks to the thumbwheel on your dashboard, a full correction is much more complicated than this common modification, and in this article, we will find out how to adjust the low beam lights of your Skoda Enyaq? For this, first of all we will find out why you should adjust your lights, and, secondly, how to adjust the low beam lights of your Skoda Enyaq.
Why adjust the low beam lights of your Skoda Enyaq?
So let’s commence our article with the interest of adjusting the low beam lights of your Skoda Enyaq. For a lot of people these lights are sufficiently adjusted, and it looks like that they light up enough at night. Unfortunately this is not necessarily the case and verifying this setting, either because the low beams of your Skoda Enyaq are not lighting up well, or because you have the feeling that they are too low or too powerful is a wise decision .
Adjusting the low beam of your Skoda Enyaq for safety is a wise decision.
First of all, the adjusting of the dipped headlights of an Skoda Enyaq must be done for a ordinary safety purpose. Regardless whether it’s for you, or for the other drivers you come across during your night journeys. In fact, if you don’t see enough, the risk is to fail to see an obstacle on the route, or to predict a curve badly. On the flip side, if your lights are too powerful, you risk dazzling the drivers in front of you, and thus putting yourself in danger. It is subsequently fundamental for others as well as for you to have an optimal setting of your parking lights.
Setting the low beam headlights of an Skoda Enyaq for legal motives
Moreover to safety, there is a law that regulates the power, the adjustment of low beams of cars, here is what it specifies: have between 2 and 4 headlights that light up at minimum , 30 meters. Another legislation regulates their use, the European one (directive 76/756/EEC), which stipulates that the height of the beam must be between 500 mm and 1200 mm from the floor, and that they must be at least 600 mm apart.
How to adjust the low-beam headlamps of a Skoda Enyaq?
We will now move on to the section that interests you the most in this article, how to adjust the low beams of his Skoda Enyaq? This setting may sound a bit difficult, but if you stick to the instructions you should be able to do it without too much difficulty.
Preparations to set the low beam of a Skoda Enyaq
Firstly, you will need to set up your motor vehicle to adjust your low beam lights in good conditions, here are the preparations to do:
- Place your motor vehicle on a floor in front of a white wall for example, about 4 or 5 meters from the wall.
- Check your tire pressure rigorously.
- Check that the height adjustment knob for the lights is set to 0
- Try doing that with half a full tank.
- Remove all unneeded weight from the motor vehicle, only one person should be in the driver’s seat.
.
The setting of the low beam headlights of his Skoda Enyaq
Once your motor vehicle is in place, you will turn on your dipped beam and make a cross-shaped mark (one horizontal and one vertical section) in the middle of the beam that will be projected on the wall. Make sure with a level that both parts of the cross are straight. Then step back your motor vehicle up to a distance of between 7 and 10 metres. For the rest of the task here are the simple steps to stick to:
- Open your bonnet, situate the screws for horizontal and vertical adjustment of the lights of your Skoda Enyaq (they are in general marked, and those above must adjust the verticality and those on the side controls the horizontality of the adjustment).
- Use a cloth or anything else to hide the light on which you are not making the adjustment.
- Using the screws to make the horizontal adjustment, you should have the most strong part of the beam which should be a little to the right of the vertical line marked on the wall
- With regard to vertical adjustment, you will have to use the screw to try to position the upper end of the beam at the level of the horizontal marking on the wall, or slightly below.
- Once done, check that the low beam setting of your Skoda Enyaq is consistent on the road, do not be reluctant to check that it has been driven, on occasion it may move.
.
If you want to adjust the fog lights on your Skoda Enyaq, please browse our article on this subject.
Whenever you have any additional questions about the Skoda Enyaq, do not hesitate to consult our Skoda Enyaq category.
