Whether you feel you can’t see properly through the night, regardless you feel you’re lighting too low or too high, in all of these circumstances, there’s only one component of your motor vehicle to blame – your low beams. Although this adjustment may seem to be easy to do thanks to the thumbwheel on your dashboard, a whole adjustment is much more complex than this basic modification, and in this article, we will find out how to adjust the low beam lights of your Jeep Wrangler? For this, first we will find out why you should adjust your lights, and, secondly, how to adjust the low beam lights of your Jeep Wrangler.
Why set the low beam lights of your Jeep Wrangler?
So let’s begin our article with the advantage of adjusting the low beam lights of your Jeep Wrangler. For most people these lights are sufficiently adjusted, and it looks like that they light up enough at night. However this is not necessarily the case and verifying this setting, either because the low beams of your Jeep Wrangler are not illuminating well, or because you have the sense that they are too low or too powerful is a wise decision .
Adjusting the low beam of your Jeep Wrangler for security is a wise decision.
First of all, the adjusting of the dipped headlights of an Jeep Wrangler must be done for a elementary security purpose. Whether it’s for you, or for the other drivers you encounter during your night trips. Indeed, if you don’t see enough, the real danger is to miss an obstacle on the road, or to predict a curve badly. On the flip side, if your lights are too powerful, you risk dazzling the people in front of you, and thus putting yourself at risk. It is therefore necessary for others as well as for you to have an optimal setting of your parking lights.
Setting the low beam headlights of an Jeep Wrangler for law justifications
In addition to security, there is a law that supervises the power, the adjustment of low beams of cars, here is what it specifies: have between 2 and 4 headlights that light up at least 30 meters. Another legislation supervises their use, the European one (directive 76/756/EEC), which stipulates that the height of the beam must be between 500 mm and 1200 mm from the floor, and that they must be at least 600 mm apart.
How to adjust the low-beam headlamps of a Jeep Wrangler?
We will now move on to the part that interests you the more in this article, how to adjust the low beams of his Jeep Wrangler? This setting may appear a bit complicated, but if you stick to the instructions you should be able to do it without too much difficulty.
Preparations to set the low beam of a Jeep Wrangler
To start, you will need to set up your motor vehicle to adjust your low beam lights in good conditions, here are the preparations to put in place:
- Place your motor vehicle on a floor in front of a white wall for example, about 4 or 5 meters from the wall.
- Check your tire pressure rigorously.
- Check that the height adjustment knob for the lights is set to 0
- Try doing that with half a full tank.
- Remove all unneeded weight from the motor vehicle, only one person should be in the driver’s seat.
.
The setting of the low beam headlights of his Jeep Wrangler
Once your motor vehicle is in place, you will switch on your dipped beam and make a cross-shaped mark (one horizontal and one vertical section) in the middle of the beam that will be projected on the wall. Make sure with a level that both parts of the cross are straight. Then move back your motor vehicle up to a distance of between 7 and 10 metres. For the rest of the procedure here are the simple steps to stick to:
- Open your bonnet, situate the screws for horizontal and vertical adjustment of the lights of your Jeep Wrangler (they are in most cases marked, and those above must adjust the verticality and those on the side handles the horizontality of the adjustment).
- Use a cloth or something else to hide the light on which you are not making the modification.
- Using the screws to make the horizontal modification, you should have the most intense part of the beam which should be a little to the right of the vertical line marked on the wall
- With regard to vertical correction, you will have to use the screw to try to position the upper end of the beam at the level of the horizontal marking on the wall, or slightly below.
- Once complete, examine that the low beam setting of your Jeep Wrangler is consistent on the road, do not be reluctant to examine that it has been driven, in some cases it may move.
.
If you want to adjust the fog lights on your Jeep Wrangler, please examine our article on this subject.
If perhaps you have any further questions about the Jeep Wrangler, do not hesitate to consult our Jeep Wrangler category.
