Whether you feel you can’t see good enough after dark, whether you feel you’re lighting too low or too high, in all of these cases, there’s only one part of your motor vehicle to blame – your low beams. Even though this adjustment may look easy to do thanks to the thumbwheel on your dashboard, a full adjustment is much more complicated than this ordinary modification, and in this content, we will see how to adjust the low beam lights of your Jeep Renegade? For this, first we will see why you should adjust your lights, and, secondly, how to adjust the low beam lights of your Jeep Renegade.

set-low-beam-headlights-jeep-renegade

Why set the low beam lights of your Jeep Renegade?

So let’s start our content with the interest of adjusting the low beam lights of your Jeep Renegade. For many people these lights are sufficiently adjusted, and it looks like that they light up enough at night. Sadly this is not always the case and looking at this setting, either because the low beams of your Jeep Renegade are not illuminating well, or because you have the sense that they are too low or too powerful is a good plan .

Adjusting the low beam of your Jeep Renegade for security is a good plan.

Firstly, the adjusting of the dipped headlights of an Jeep Renegade must be done for a ordinary security purpose. Regardless whether it’s for you, or for the other drivers you encounter during your night journeys. In fact, if you don’t see enough, the real danger is to fail to see an obstacle on the route, or to predict a curve badly. However, if your lights are too powerful, you risk dazzling the car owners in front of you, and thus putting yourself at risk. It is as a consequence necessary for others as well as for you to have an ideal setting of your parking lights.

Setting the low beam headlights of an Jeep Renegade for legal justifications

In addition to security, there is a law that controls the power, the adjustment of low beams of cars, here is what it specifies: have between 2 and 4 headlights that illuminate at least 30 meters. Another legislation controls their use, the European one (directive 76/756/EEC), which stipulates that the height of the beam must be between 500 mm and 1200 mm from the ground, and that they must be at least 600 mm apart.

How to adjust the low-beam headlamps of a Jeep Renegade?

We will now go forward to the section that interests you the most in this content, how to adjust the low beams of his Jeep Renegade? This setting may seem a bit complex, but if you stick to the instructions you should be able to do it without too much difficulty.

Preparations to set the low beam of a Jeep Renegade

First of all, you will need to prepare your motor vehicle to adjust your low beam lights in good conditions, here are the preparations to do:

  • Place your motor vehicle on a floor in front of a white wall for example, about 4 or 5 meters from the wall.
  • Check your tire pressure cautiously.
  • Check that the height adjustment knob for the lights is set to 0
  • .

  • Try doing that with half a full tank.
  • Remove all unnecessary weight from the motor vehicle, only one person should be in the driver’s seat.

The setting of the low beam headlights of his Jeep Renegade

Once your motor vehicle is into position, you will switch on your dipped beam and make a cross-shaped mark (one horizontal and one vertical section) in the middle of the beam that will be projected on the wall. Make sure with a level that both parts of the cross are straight. Then move back your motor vehicle up to a distance of between 7 and 10 metres. For the rest of the procedure here are the steps to stick to:

  • Open your bonnet, identify the screws for horizontal and vertical adjustment of the lights of your Jeep Renegade (they are in most cases marked, and those above must adjust the verticality and those on the side handles the horizontality of the adjustment).
  • Use a cloth or some thing else to hide the light on which you are not making the correction.
  • Using the screws to make the horizontal correction, you should have the most intense part of the beam which should be a little to the right of the vertical line marked on the wall
  • .

  • With regard to vertical manipulation, you will have to use the screw to try to position the upper end of the beam at the level of the horizontal marking on the wall, or slightly below.
  • Once complete, check that the low beam setting of your Jeep Renegade is consistent on the road, do not be reluctant to check that it has been driven, on occasion it may move.

If you want to adjust the fog lights on your Jeep Renegade, please browse our content on this subject.

If you want more guides on the Jeep Renegade, go to our Jeep Renegade category.