Regardless you feel you can’t see properly after dark, regardless whether you feel you’re lighting too low or too high, in all of these occasions, there’s only one component of your motor vehicle to blame – your low beams. Even though this correction may seem easy to do thanks to the thumbwheel on your dashboard, a complete correction is much more technical than this ordinary modification, and in this article, we will find out how to adjust the low beam lights of your Jeep Compass? For this, first we will find out why you should adjust your lights, and, secondly, how to adjust the low beam lights of your Jeep Compass.
Why adjust the low beam lights of your Jeep Compass?
So let’s begin our article with the interest of adjusting the low beam lights of your Jeep Compass. For most people these lights are sufficiently adjusted, and it looks like that they light up enough at night. Unfortunately this is not necessarily the case and checking out this setting, either because the low beams of your Jeep Compass are not lighting up well, or because you have the feeling that they are too weak or too powerful is a wise decision .
Adjusting the low beam of your Jeep Compass for safety is a wise decision.
To start, the adjusting of the dipped headlights of an Jeep Compass must be done for a basic safety purpose. Whether it’s for you, or for the other drivers you encounter during your night journeys. In reality, if you don’t see enough, the real danger is to fail to see an obstacle on the route, or to predict a curve badly. On the other hand, if your lights are too powerful, you risk dazzling the car owners in front of you, and thus putting yourself in danger. It is therefore necessary for others as well as for you to have an optimal setting of your parking lights.
Setting the low beam headlights of an Jeep Compass for law motives
Additionally to safety, there is a law that regulates the power, the adjustment of low beams of cars, here is what it specifies: have between 2 and 4 headlights that illuminate at least 30 meters. Another regulation regulates their use, the European one (directive 76/756/EEC), which stipulates that the height of the beam must be between 500 mm and 1200 mm from the ground, and that they must be at least 600 mm apart.
How to adjust the low-beam headlamps of a Jeep Compass?
We will now move on to the part that interests you the most in this article, how to adjust the low beams of his Jeep Compass? This setting may appear a bit difficult, but if you follow the recommendations you should be able to do it without too much problem.
Preparations to set the low beam of a Jeep Compass
Firstly, you will need to prepare your motor vehicle to adjust your low beam lights in good conditions, here are the preparations to apply:
- Place your motor vehicle on a area in front of a white wall for example, about 4 or 5 meters from the wall.
- Examine your tire pressure cautiously.
- Examine that the height adjustment knob for the lights is set to 0
- Try doing that with half a full tank.
- Remove all needless weight from the motor vehicle, only one person should be in the driver’s seat.
.
The setting of the low beam headlights of his Jeep Compass
Once your motor vehicle is into position, you will switch on your dipped beam and make a cross-shaped mark (one horizontal and one vertical section) in the middle of the beam that will be projected on the wall. Make sure with a level that both parts of the cross are straight. Then move back your motor vehicle up to a distance of between 7 and 10 metres. For the rest of the operation here are the simple steps to follow:
- Open your bonnet, identify the screws for horizontal and vertical adjustment of the lights of your Jeep Compass (they are usually marked, and those above must adjust the verticality and those on the side adjusts the horizontality of the adjustment).
- Use a cloth or anything else to hide the light on which you are not making the modification.
- Using the screws to make the horizontal modification, you should have the most powerful part of the beam which should be a little to the right of the vertical line marked on the wall
- With regard to vertical modification, you will have to use the screw to try to position the upper end of the beam at the level of the horizontal marking on the wall, or slightly below.
- Once finished, verify that the low beam setting of your Jeep Compass is consistent on the road, do not hesitate to verify that it has been driven, in some cases it may move.
.
If you want to adjust the fog lights on your Jeep Compass, please go through our article on this subject.
To discover more tips on the Jeep Compass, take a look at the Jeep Compass category.
