Whether you feel you can’t see good enough during the night, whether you feel you’re lighting too low or too high, in all of these situations, there’s only one part of your car to blame – your low beams. Although this correction may seem to be easy to do thanks to the thumbwheel on your dashboard, a full correction is much more complex than this basic modification, and in this article content, we will discover how to adjust the low beam lights of your Ds Ds 3 Crossback? For this, first we will discover why you should adjust your lights, and, secondly, how to adjust the low beam lights of your Ds Ds 3 Crossback.
Why set the low beam lights of your Ds Ds 3 Crossback?
So let’s commence our article content with the advantage of adjusting the low beam lights of your Ds Ds 3 Crossback. For many people these lights are well enough adjusted, and it seems that they light up enough at night. Unfortunately this is not always the case and checking out this setting, either because the low beams of your Ds Ds 3 Crossback are not lighting up well, or because you have the feeling that they are too weak or too powerful is a good plan .
Adjusting the low beam of your Ds Ds 3 Crossback for safety is a good plan.
To begin, the adjusting of the dipped headlights of an Ds Ds 3 Crossback must be done for a basic safety cause. Whether it’s for you, or for the other drivers you encounter during your night trips. In reality, if you don’t see enough, the risk is to miss an obstacle on the road, or to anticipate a curve badly. However, if your lights are too powerful, you risk dazzling the car owners in front of you, and thus putting yourself in danger. It is therefore necessary for others as well as for you to have an optimal setting of your parking lights.
Setting the low beam headlights of an Ds Ds 3 Crossback for law reasons
Additionally to safety, there is a law that supervises the power, the adjustment of low beams of cars, here is what it specifies: have between 2 and 4 headlights that light up at least 30 meters. Another regulation supervises their use, the European one (directive 76/756/EEC), which stipulates that the height of the beam must be between 500 mm and 1200 mm from the ground, and that they must be at least 600 mm apart.
How to adjust the low-beam headlamps of a Ds Ds 3 Crossback?
We will now move on to the part that interests you the most in this article content, how to adjust the low beams of his Ds Ds 3 Crossback? This setting may seem to be a bit complicated, but if you stick to the guidelines you should be able to do it without too much problem.
Preparations to set the low beam of a Ds Ds 3 Crossback
First of all, you will need to set up your car to adjust your low beam lights in good conditions, here are the preparations to put in place:
- Place your car on a area in front of a white wall for example, about 4 or 5 meters from the wall.
- Verify your tire pressure cautiously.
- Verify that the height adjustment knob for the lights is set to 0
- Try doing that with half a full tank.
- Remove all unnecessary weight from the car, only one person should be in the driver’s seat.
.
The setting of the low beam headlights of his Ds Ds 3 Crossback
Once your car is in place, you will switch on your dipped beam and make a cross-shaped mark (one horizontal and one vertical section) in the middle of the beam that will be projected on the wall. Make sure with a level that both parts of the cross are straight. Then back your car up to a distance of between 7 and 10 metres. For the rest of the procedure here are the steps to stick to:
- Open your bonnet, locate the screws for horizontal and vertical adjustment of the lights of your Ds Ds 3 Crossback (they are in general marked, and those above must adjust the verticality and those on the side manages the horizontality of the adjustment).
- Use a cloth or something else to hide the light on which you are not making the adjustment.
- Using the screws to make the horizontal adjustment, you should have the most strong part of the beam which should be a little to the right of the vertical line marked on the wall
- With regard to vertical modification, you will have to use the screw to try to position the upper end of the beam at the level of the horizontal marking on the wall, or slightly below.
- Once completed, check that the low beam setting of your Ds Ds 3 Crossback is consistent on the road, do not hesitate to check that it has been driven, sometimes it may move.
.
If you want to adjust the fog lights on your Ds Ds 3 Crossback, please go through our article content on this subject.
If you have any additional questions about the Ds Ds 3 Crossback, do not hesitate to consult our Ds Ds 3 Crossback category.
