Being the target of recurring problems on your automobile is specially frustrating, furthermore the financial side that these complications represent, one must also add the time lost with a non-operational Mazda 6 and the time spent to identify and remedy the breakdown. However, some problems are less severe than others, which is not to say that they do not stress us. Today we are going to take a look at a issue that can occur to everyone, feeling vibrations at acceleration on Mazda 6. This issue can often be complex to perceive but it must be dealt with. We will consequently start our content page with the roots of these vibrations on Mazda 6, then, with the answers you have to reduce or stop these tremors.

acceleration-vibrations-mazda-6

Why does my Mazda 6 make vibrations when accelerating?

So let’s start our content page with the roots of this sort of issue on your car. You should already know that an engine, especially if it is ancient or if it has been driven quite a lot, can naturally vibrate without being a issue behind it. Large diesel engines, especially those with a lot of torque, can cause this sort of feeling, both at idle and when accelerating.

I feel vibrations on my Mazda 6 only when accelerating

Let’s take the most interesting case for us in this content page. The fact that you experience trembling on your Mazda 6 during your acceleration phases, in this situation you will have to verify the state of some components because many of elements can be at the beginning of these vibrations and whether or not you are unlucky a combination of several of them may also be possible, here is the list of components that can be concerned.

  • Turbo: If the turbo of your Mazda 6 is faulty, it may cause vibrations that you will come to feel when you accelerate at the moment it is turned on.
  • The turbo pressure sensor: This sensor will control the pressure exerted in the turbo of your car, if it fails it may disturb the performance of your turbo and make vibrations that you may experience during acceleration of your Mazda 6.

    • .

  • If the turbo is punctured or ruined, the consequence will be the same, the power supply of your turbo will be disturbed and its performance too. Remember to visually check their condition.

I’m experiencing vibrations on my Mazda 6 at acceleration and deceleration

We will now look into the case where you experience vibrations on your Mazda 6 when you are accelerating but also when you are idling. If you only experience vibrations when you are idling on your Mazda 6, please have a look at our content page dedicated to this issue to fix your problem. If, alternatively, you identify that your Mazda 6 vibrates when accelerating but also when it is stopped, here is the list of elements to check:

  • EGR valve: In truth this valve which manages the return of exhaust gases for pollution standards can become dirty and disrupt the evacuation of exhaust gases which can cause Mazda 6 vibrates when accelerating but also when stopped.
  • Injectors: Your injectors that regulating the fuel/air mixture flow may be dirty or damaged, which will discharge the wrong amount of mixture and thus prevent your engine block from working properly, it is even possible that one or more of your cylinders are not running correctly.
  • Fuel Filter: Like the injectors, if the filter is clogged it will not let the fuel pass correctly and therefore disrupt the performance of your Mazda 6, up to the point of causing vibrations during acceleration.

Here are the most important causes of a Mazda 6 that vibrates at acceleration

What can I do to stop the vibration when I accelerate on my Mazda 6? What can I do?

To finish , in this last section, we will give you the answers available to you to cure these tremors on your car when you accelerate. Here is the best attitude to adopt in accordance with the component that is affected:

  • Turbo: If your turbo starts all these vibrations when you accelerate your Mazda 6, it will be good for you to control all the components linked to it because changing a complete turbo is a big budget and in most cases the issue does not come exclusively from the turbo. So make sure you take a look at your turbo pressure sensor, your flowmeter, the EGR valve and the hoses of your turbo. Otherwise take your Mazda 6 to your garage area.
  • EGR valve: The EGR valve has the advantage that it is quite often easy to access and simple to disassemble/clean. You can always look into it and clean it, for this see our content page on cleaning the EGR valve of an Mazda 6.
  • Injectors: Injectors are very delicate components and a few impurities may be enough to disrupt their performance. Use a fuel additive to simply clean the injectors, if this is not enough you will have to go to a professional.
  • Fuel Filter: If it is the fuel filter, simply replace it. A fuel filter doesn’t clean itself, so if it is clogged you will basically have to replace it with a new one.

Now you have all the info you need to locate the source of the vibrations at acceleration on your Mazda 6. If you don’t feel able to conduct certain operations don’t hesitate to go to your technician.

If you wish more tutorials on the Mazda 6, go to our Mazda 6 category.