Keeping an eye on your car is imperative in these days, in fact, if you do not do the minimum routine service of it, or if you do not take into account alerts of abnormality, you strongly risk to see your car getting in bad conditions. This is precisely the subject we are gonna talk about in this article, one of the indicators that most disturbs motorists is the ABS warning light on Mazda 2. In an attempt to help you review this warning light, we will first look at what this ABS warning light corresponds to, then in a second what to do if the ABS light is on Mazda 2?.
What does the ABS light on Mazda 2 indicate?
We will start our article content with the definition of an ABS warning light on Mazda 2, to do this, in first, we will find out what an ABS is, and later on, why the ABS light on your car lights up.
What is the ABS on Mazda 2?
To begin with, it is fundamental to describe to you what the ABS of your Mazda 2 is employed for so that you can understand the remaining of this guideline. The ABS (Anti-lock Braking System) is a system that prevents the wheels of your car from locking during braking. The aim of this system is to optimize the braking distance of a car by preventing the wheels from locking, sliding on the road and you losing control of your car. The ABS system of your Mazda 2 is composed of several components, here they are:
- Speed sensors on each wheel, which will review if one of the wheels locks up.
- A hydraulic system and valves that will control the pressure of the pads on the discs to control the braking power of the car
- A computer that is the control center of your entire ABS system as well as the ABS light of your Mazda 2
The fact is, you can simply come to feel how your car’s ABS works. If you have to steer, you will find that your car will brake by pawing, this is exactly the behaviour that ABS permits, it will optimise braking to the maximum by relating the phases of pressure on the brake discs and the phases of discharge to prevent the wheels from locking up.
Meaning of an ABS light on Mazda 2
Now we go forward to the part that you are most certainly more curious about, meaning of an ABS warning light on a Mazda 2? To begin with, it is an orange light, so if it is on it shows that your ABS system is faulty. You should be aware that when the ABS warning light is on, the ABS will be put into safety mode, so you should adjust your driving and not take any risks. Here are the different problems that the ABS warning light on your Mazda 2 can signal:
- It could be a simple short circuit, a damaged wiring harness, a faulty relay or fuse. Use a pressure gauge to verify it.
- A malfunctioning ABS sensor: A failure of one of them triggers the ABS light on your Mazda 2 to turn on
- The ABS hydraulic block of your Mazda 2: If it is faulty it is possible that the indicator light will come on and you will no longer be able to use your ABS.
- The ABS computer: If the computer has a trouble, being the center of all decisions made to run your ABS, the light will undoubtedly turn on.
What if the ABS light activate on my Mazda 2?
We will now go forward to the part where we will try to give you some solutions to switch off this light, and thus answer the following question, what to do if the ABS light is on on my Mazda 2?. The solutions will be based upon the failure you are going through. To begin with, pass your Mazda 2 to the diagnostic tool, if you don’t know how to read a fault code on Mazda 2, don’t hesitate to examine our guideline which points the steps to take. Once you have found the origin of your trouble, here are the steps to take to correct it and turn off the ABS light on your Mazda 2:
- Problem of the ECU or the hydraulic block: It can only be adjusted, and in this situation, you will have to go through a specialist, but if it’s dead, it could cost you around 1000€ to change the ECU and 1500 to 2000€ if you have to change both of them.
- Electrical trouble: Once you’ve detected an electrical trouble with your manometer, if it’s only a fuse or a relay, count around 10€ maximum, in any other case you’ll have to repair the wiring harness.
- A faulty sensor: In some cases a simple cleaning of the sensors will be enough to remedy the trouble, in any other case changing a sensor can cost up to a few hundred euros.
If perhaps you have any additional questions about the Mazda 2, do not hesitate to consult our Mazda 2 category.